★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000080devices tracked

Home › Devices › Apple › iPhone 3GS

[ device photo ]NEW!

APPLE · PHONE · 2009

iPhone 3GS

Also called: iPhone 3GS · 3GS · A1303 · A1325

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 12 sources · 2 item(s) unverified

2009 plastic-backed iPhone with a replaceable battery, front glass and LCD, and 30-pin dock. Software side: Legacy iOS Kit restore/downgrade and jailbreak on every release from iOS 3.0 to 6.1.6, plus the alloc8 bootrom exploit. Historical openiBoot builds exist for dual-boot experiments.[1][2][9][8][10]

5MODS
4WORK
1EXPERIMENTAL
12SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
A1303iPhone 3GS2009Plastic back. Model number A1303 on the back cover. Mini-SIM tray on the top edge; serial on the tray. Back imprint is the same bright silver as the Apple logo (3G imprint is duller).[1][5]
A1325iPhone 3GS2009Same plastic-back 3GS family; model number A1325 on the back cover.[1]
Specs
Storage8, 16, or 32 GB[1]
Battery3.7 V Li-ion, about 1219 mAh (4.51 Wh); not soldered to the board[5]
ColorsBlack and white[1]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Battery replacementWorks
BatteryDifficulty: mediumOpens caseNo solderingReversible20-30 min
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Open the case, lift the display, remove the logic board, and pry the adhesive-held Li-ion pack out of the rear case.[2][5]

Special tools: Phillips #00 screwdriver, suction cup, spudger

Parts

  • iPhone 3GS battery Fits — Drops into the rear case after the logic board is out; not soldered to the board.[2][5]

Good to know

  • The battery is not soldered to the logic board.[5]
  • Stock pack is listed as 3.7 V and 4.51 Wh (about 1219 mAh).[5]
  • The pack sits under the logic board, so the board has to come out before the battery.[2][5]
  • Mild adhesive holds the pack to the rear case. Do not puncture or bend the cell.[2]

⚠ Watch out

  • A small golden grounding tab next to the "Do not remove" sticker snags easily when lifting the logic board and can cause signal problems if bent.[2]
  • If you heat the case to loosen adhesive, keep heat low. Overheating can ignite the battery.[2]

Guides:iPhone 3GS Battery Replacement - iFixit Repair Guide

Display (glass and LCD)Works
ScreenDifficulty: hardOpens caseNo solderingReversible30 min

Replace a cracked digitizer or dead LCD. On the 3GS the front glass and LCD are separate, not laminated.[3][5]

Special tools: Phillips #00 screwdriver, suction cup, spudger, metal spudger

Parts

  • iPhone 3GS display assembly Fits — Front glass and LCD can be replaced separately after the assembly is out.[3][5]

Good to know

  • LCD and front glass are not fused and can be replaced individually.[5][3]
  • Several ribbon cables, numbered 1 to 3 in the guide, hold the display. The FPC latch on cable 3 is delicate.[3][5]

⚠ Watch out

  • Tape over cracked glass before you pry, and wear eye protection. Glass shards come free easily.[3]
  • The FPC locking latch on cable 3 is delicate. Open it before sliding the ribbon out or back in.[3]

Guides:iPhone 3GS Display Replacement - iFixit Repair Guide

30-pin dock connectorWorks
ChargingDifficulty: mediumOpens caseNo solderingReversible

Replace the lower dock-connector assembly that carries the 30-pin port, antenna contact, and lower speaker connections.[4]

Special tools: Phillips #00 screwdriver, suction cup, spudger

Parts

  • iPhone 3GS dock connector assembly Fits — Full lower assembly; screw holes must sit above the bezel holes on install.[4]

Good to know

  • The assembly connects the phone to a computer or charger over the 30-pin cable.[4]
  • Replacing it means opening the case and removing the logic board, same deep path as the battery job.[4]

⚠ Watch out

  • Watch the small golden grounding tab when lifting the logic board; it breaks easily and affects reception.[4]
  • A reader comment on the guide reports the Home button stopped working when the gold contacts on the dock assembly were bent out of line.[4]

Guides:iPhone 3GS Dock Connector Replacement - iFixit Repair Guide

Jailbreak (root access)Works
SoftwareDifficulty: noneCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Install a jailbreak for unsigned software and root filesystem access. Legacy iOS Kit covers every release from iOS 3.0 to 6.1.6; older guides use redsn0w or a custom ramdisk.[9][6][7][8]

Good to know

  • Legacy iOS Kit jailbreaks the 3GS on all release versions from iOS 3.0 to 6.1.6.[9]
  • Legacy iOS Kit also restores and downgrades the 3GS, including unsigned versions without blobs.[9]
  • A community redsn0w walkthrough targets a 3GS updated to iOS 6.1.6 and uses an iOS 6.0 IPSW inside redsn0w, with the phone in DFU mode.[6]
  • A custom-ramdisk "barebones" jailbreak for iOS 6.1.6 gains root filesystem read/write and patches Services.plist (AFC2).[7]
  • alloc8 is an untethered bootrom exploit that affects both old and new 3GS bootrom revisions (old bootrom is also vulnerable to the faster 24Kpwn).[8]

⚠ Watch out

  • Back up before you jailbreak. Guides warn about data loss.[6]
  • The barebones ramdisk tutorial expects a Windows 7 host for limera1n; it notes limera1n broken on Windows 10.[7]

Guides:GitHub - LukeZGD/Legacy-iOS-Kit: An all-in-one tool to restore/downgrade, save SHSH blobs, jailbreak legacy iOS devices, and moreHow to Jailbreak iPhone 3GS with redsn0w! | MacRumors ForumsBarebones jailbreak iOS 6

openiBoot (alternative OS bootloader)Experimental
SoftwareDifficulty: hardCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Open-source bootloader from the iDroid project. Historical dual-boot path for experimental Android (iDroid) builds; not a modern LineageOS or TWRP install.[10][11][12]

Good to know

  • openiBoot has a compile target for the iPhone 3GS (`scons iPhone3GS`).[10]
  • From version 0.3 it uses a grub-style menu (`/boot/menu.lst`) that can boot iOS or an Android kernel/initrd pair.[10]
  • The 3GS is not on the official LineageOS or TWRP device lists; this path is the historical openiBoot / iDroid route.[11][12][10] unverified

⚠ Watch out

  • Version 0.3 and above will not boot iDroid 2.6.32-series kernels without extra kernel parameters.[10]

Guides:No guide found yet.

Sources (12)

SOURCES.TXT