Home › Devices › Apple › iPhone 4
APPLE · PHONE · 2010-2011
iPhone 4
Also called: iPhone 4 · A1332 · A1349
Glass-sandwich iPhone with a slide-off rear panel, easy battery swap, fused Retina display, and 30-pin dock. Software: Legacy iOS Kit restore/downgrade and jailbreak, CoolBooter dual-boot of a second iOS install, and ipwndfu pwned-DFU tools for the A4 (S5L8930) bootrom.[1][2][5][8][7][9]
Which one do I have?
Specs
Mods (6)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Rear glass panelWorks
Remove two bottom screws and slide the rear glass panel up to open the phone or swap a cracked back.[4]
Special tools: Phillips #00 or pentalobe screwdriver
Parts
- iPhone 4 rear glass panel Fits — Slides on after the two bottom screws are out.[4]
Good to know
- Push the rear panel toward the top edge; it moves about 2 mm, then lifts off.[4]
- Bottom screws may be Phillips or 5-point pentalobe, depending on the unit.[4]
Guides:iPhone 4 Rear Panel Replacement - iFixit Repair Guide
Battery replacementWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
Slide off the rear panel, undo the battery connector screw, and lift the pack with its pull tab.[2][3]
Special tools: Phillips #00 or pentalobe screwdriver, spudger
Parts
- iPhone 4 battery Fits — Connects with a single screw-retained connector on the logic board.[2]
Good to know
- Replacing the battery needs only minimal disassembly once the rear panel is off.[2]
- A single 2.5 mm Phillips screw secures the battery connector to the logic board.[2]
- After install, calibrate by charging to 100%, then running down to shutdown at least once.[2]
⚠ Watch out
Guides:iPhone 4 Battery Replacement - iFixit Repair GuideHow to replace the iPhone 4 battery | iMore
Retina display assemblyWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
Replace the fused front glass, digitizer, and LCD as one assembly. Near-complete teardown.[5]
Special tools: Phillips #00 or pentalobe screwdriver, spudger
Parts
- iPhone 4 display assembly Fits with conditions — iFixit guide is written for the GSM/AT&T model; it does not cover the CDMA model.[5]
Good to know
- The replacement gives you a new front glass panel, digitizer, and LCD together.[5]
- Pry the upper edge of the front panel assembly away from the steel inner frame to separate it.[5]
⚠ Watch out
- Power off first. Avoid puncturing the battery while the phone is open.[5]
Guides:iPhone 4 (GSM/AT&T) Screen Replacement - iFixit Repair Guide
30-pin dock connectorWorks
Replace the dock connector assembly, which includes the 30-pin port and lower microphone.[6]
Special tools: Phillips #00 or pentalobe screwdriver, spudger
Parts
- iPhone 4 dock connector assembly Fits with conditions — iFixit lists separate GSM and CDMA dock connector parts; match the part to your model.[6]
Good to know
- The assembly includes the dock connector and lower microphone.[6]
Guides:iPhone 4 Dock Connector Replacement - iFixit Repair Guide
Jailbreak and restore (Legacy iOS Kit)Works
- ⚠ Can brick A mistake can leave the device unable to start.
- ⚠ Data loss Can erase what is on the device. Back up first.
- ⚠ Check the law May break a law or rule where you live.
Restore, downgrade, and jailbreak with Legacy iOS Kit. GSM units also support hacktivation. ipwndfu adds pwned DFU via the SHAtter exploit on S5L8930.[8][9]
Good to know
- Legacy iOS Kit supports restore, SHSH blobs, and jailbreak on 32-bit iOS devices including the iPhone 4, and restores without blobs on iPhone 4 GSM and CDMA.[8]
- Hacktivation (activate without a valid SIM) is listed for iPhone 4 GSM.[8]
- ipwndfu can put S5L8930 devices into pwned DFU with the SHAtter exploit.[9]
⚠ Watch out
- The ipwndfu exploit is not reliable and may need to be repeated if it fails.[9]
CoolBooter dual-boot iOSWorks
- ⚠ Can brick A mistake can leave the device unable to start.
- ⚠ Data loss Can erase what is on the device. Back up first.
On a jailbroken iPhone 4, install a second iOS (5 or later) alongside the current one and choose at boot.[7]
Good to know
- CoolBooter dual-boots another iOS install with your current jailbroken iOS.[7]
- Supports going from any jailbroken iOS 5 or later to a supported iOS 5 or later firmware on the iPhone 4.[7]
- Install by adding https://coolbooter.com as a Cydia source.[7]
⚠ Watch out
- Partition operations can cause data loss on failure. Back up first, and only use a phone you are willing to factory-reset.[7]
Guides:CoolBooter
Sources (9)
- official Identify your iPhone model - Apple Support · 2026-11-16
- docs iPhone 4 Battery Replacement - iFixit Repair Guide · 2026-11-16
- blog How to replace the iPhone 4 battery | iMore · 2026-11-16
- docs iPhone 4 Rear Panel Replacement - iFixit Repair Guide · 2026-11-16
- docs iPhone 4 (GSM/AT&T) Screen Replacement - iFixit Repair Guide · 2026-11-16
- docs iPhone 4 Dock Connector Replacement - iFixit Repair Guide · 2026-11-16
- official CoolBooter · 2026-11-16
- official GitHub - LukeZGD/Legacy-iOS-Kit · 2026-11-16
- official GitHub - axi0mX/ipwndfu: open-source jailbreaking tool for many iOS devices · 2026-11-16