★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000080devices tracked

Home › Devices › Apple › Apple Newton MessagePad

[ device photo ]NEW!

APPLE · PDA

Apple Newton MessagePad

Also called: Newton · MessagePad 2000 · MessagePad 2100 · MessagePad 130

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 8 sources · 1 item(s) unverified

Apple's Newton MessagePad line. The 2000/2100 StrongARM models share battery rebuilds, EL backlight foil swaps, and a hidden modem expansion port used for a DIY WiFi card. Earlier 110/120/130 packs rebuild differently and should stay on NiCd cells for the stock charger.[7][3][6][4][1]

4MODS
3WORK
1EXPERIMENTAL
8SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
MessagePad 2100NMP 21001997Announced November 1997. Same as the MessagePad 2000 but with 8 MB RAM. Newton OS 2.1.[8][7]
MessagePad 2000NMP 2000—StrongARM MessagePad with two PCMCIA slots. Effectively identical to the 2100 except for less RAM.[7]
MessagePad 110 / 120 / 1301x0 series—Earlier MessagePads with a different battery pack and charger curve. Battery rebuild guides are separate from the 2000/2100 pack.[6]
Specs
CPU (2100)162 MHz StrongARM 110[7]
Display (2100)480×320, 16-level grayscale[8]
RAM (2100)8 MB (2000 had less; 2100 is otherwise identical)[7][8]
Slots (2000/2100)Two Type II PCMCIA slots[7]

Mods (4)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Rebuild MessagePad 2000/2100 battery packWorks
BatteryDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Open the glued pack and replace dead cells with tabbed NiMH AAs. Keep the thermal switch and solder lugs A/B/C intact.[3][2]

Parts

  • NiMH AA cells with solder tabs Fits with conditions — For MessagePad 2000/2100 packs. Prefer pre-tabbed cells; do not solder bare terminals.[3][2]

Good to know

  • Hackaday confirms aged Newton packs can be rebuilt with modern rechargeable AA cells; the glued case is hard to pry open, so the video cuts a hatch into the top.[2]
  • The guide for 2000/2100 packs uses NiMH AA cells with pre-welded tabs and documents thermal-switch wiring at lugs A, B, and C.[3]

⚠ Watch out

  • Soldering directly onto bare cell terminals is discouraged; use tabbed cells.[3]

Guides:Rebuild MessagePad 2000 / 2100 battery packApple Newton Gets Rebuilt Battery Pack

Rebuild MessagePad 110/120/130 battery packWorks
BatteryDifficulty: hardOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Refurbish the earlier 1x0 pack with four NiCd AA cells. Do not use NiMH; the charger was designed for NiCd.[6]

Parts

  • NiCd cells for MessagePad 1x0 pack Fits with conditions — MessagePad 110/120/130 only. The guide advises against NiMH with the stock charger circuit.[6]

Good to know

  • The 1x0 rebuild guide advises against NiMH cells: the charger was designed for NiCd, so NiMH would not be charged properly and are more likely to be harmed over time.[6]
  • The guide pries off the two metal plates with a knife used as a lever and uses epoxy to hold the new cells; no soldering is described.[6]

Guides:Rebuild MessagePad 110 / 120 / 130 battery pack

Backlight foil replacement (2000/2100)Works
ScreenDifficulty: hardOpens caseFine solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Replace a dim or dead backlight foil on the MessagePad 2000 or 2100. Requires opening the unit and desoldering the old panel.[4][5]

Good to know

  • The guide covers replacing the backlight foil on the MessagePad 2000 or 2100, including unsoldering the wires from the old foil.[4]
  • Full teardown unlocks display ribbon connector J9 by pushing the two white tabs outward toward the cable.[5]

Guides:Replace MessagePad 2000 / 2100 backlightDisassemble MessagePad 2000 / 2100

WiFi card via internal modem port (2000/2100)Experimental
ConnectivityDifficulty: expertOpens caseFine solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

The MessagePad 2100 has a hidden internal port for a modem card that Apple never made. One project built a WiFi card for it around a WiReach module.[1]

Parts

  • WiReach WiFi module (ConnectOne) Fits with conditions — Used in one build on a MessagePad 2100, connected to the internal serial port; design files are on GitHub.[1]

Good to know

  • There is a hidden port for a modem card that Apple never made. One Hackaday project built a WiFi card for it using a WiReach module, not an ESP8266.[1] unverified

Guides:Giving WiFi To An Apple Newton

Sources (8)

SOURCES.TXT