★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000080devices tracked

Home › Devices › Atari › Atari Lynx

[ device photo ]NEW!

ATARI · HANDHELD CONSOLE · 1989-1991

Atari Lynx

Also called: Lynx I · Lynx II · Lynx 1 · Lynx 2

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 10 sources

Atari's color handheld (Lynx I in 1989, smaller Lynx II in 1991). Both use the Mikey and Suzy chips. Common work is a modern IPS or McWill LCD in place of the tube-lit screen, a flash cartridge for homebrew and your own cartridge backups, and replacing the power MOSFET and zener before a failure puts 9 V on the 5 V rails.[1][2][3][9]

4MODS
4WORK
0EXPERIMENTAL
10SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
C103949-001Lynx I1989Original larger Lynx. Board part number C103949-001. Mono headphone jack. Power MOSFET is Q11; zener is ZD1.[2][1][3]
Lynx IIC104129-001 Rev A, C104424-001 Rev 1, or C104471-001 Rev A1991Smaller case, stereo headphone jack. Board uses one of those three part numbers. Power MOSFET is Q12; zener is D13.[2][1][3]
Specs
ChipsU1 Mikey (CPU / sound / DMA); U2 Suzy (graphics / blitter)[2]
DC inputCenter-positive 9 V barrel, 3.5 mm × 1.3 mm[4]

Mods (4)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Flash cartridgeWorks
StorageDifficulty: noneCase stays closedNo solderingReversible

A flash cart runs homebrew and your own cartridge backups. Options include the RetroHQ Lynx GameDrive and the BennVenn ElCheapoSD.[1]

Parts

  • RetroHQ Lynx GameDrive Fits — Flash cartridge listed for the Lynx.[1]
  • BennVenn ElCheapoSD Fits — Flash cartridge listed for the Lynx.[1]

Good to know

  • RetroRGB lists the RetroHQ Lynx GameDrive and the BennVenn ElCheapoSD as Lynx flash cartridges.[1]

Guides:No guide found yet.

BennVenn IPS LCDWorks
ScreenDifficulty: mediumOpens caseNo solderingReversible

Replace the CCFL-backlit panel with a BennVenn IPS kit. One driver board supports Lynx I and Lynx II. Lynx II can use a solderless flex; Lynx I bridges a jumper on the PCB.[9][8][10][5]

Parts

  • BennVenn Lynx IPS LCD kit Fits with conditions — Single PCB for Lynx I and Lynx II; bridge the Lynx1 jumper for Lynx I. Lynx II drop-in uses a custom flex; C104129-001 needs an extra wire and a ribbon-trace cut (or the Lynx I board with a Lynx II bracket).[9][8] Buy: bennvenn.myshopify.com · zedlabz.com

Good to know

  • The kit replaces the tube-lit screen with an IPS panel and lowers power use.[9][10][8]
  • One PCB supports Lynx I and Lynx II. Bridge the Lynx1 jumper when installing in a Lynx I.[9]
  • On Lynx II, the ZedLabz listing is a solderless install with a custom ribbon, a 3D-printed alignment bracket, and brightness on the original wheel. C104129-001 needs an extra soldered wire and a cut on the ribbon, or the Lynx I board with a Lynx II bracket.[8]
  • Kits can add hardware scanline emulation and, on some installs, brightness on the backlight button.[9][10]

⚠ Watch out

  • Recap and confirm the Lynx works before fitting the LCD kit.[8]
  • On C104129-001, the Lynx II solderless kit needs an extra soldered wire and a cut on the ribbon cable.[8]

Guides:No guide found yet.

McWill LCD (and optional VGA out)Works
ScreenDifficulty: hardOpens caseFine solderingPermanent4-8 hours
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

McWill's LCD kit replaces the original screen with a modern one. Install needs fine soldering, removal of the high-voltage backlight parts, and a voltage check before the new board is powered. Optional VGA out needs a shell cut.[1][6][7][5]

Parts

  • McWill Lynx LCD kit Fits with conditions — Separate Lynx I and Lynx II installs. Optional VGA connector; skip it if you do not want to cut the shell.[1][6][7]

Good to know

  • McWill offers Lynx LCD and VGA kits. The LCD replaces the original screen; TV-out kits can output 480p VGA from a port on the top of the system.[1]
  • On Lynx I, the build replaces the voltage regulator parts (zener, MOSFET, two 3906 transistors, power jack) and needs confident SMD soldering. One build log wired VGA where the brightness pot was and cut plastic to fit the connector.[6]
  • On Lynx II, desolder the CFL backlight circuit parts, add ground and VCC wires, and confirm the 5 V rail stays under 5.45 V before connecting the screen board. VGA can be left unused to avoid cutting the shell.[7]

⚠ Watch out

  • If you are not sure about soldering skills, do not attempt this mod.[6]
  • Measure the 5 V rail after the backlight parts are removed. Do not connect the McWill board if the rail exceeds 5.45 V.[7]

Guides:Modding the Atari Lynx Portable with McWill Screen, New CapsAtari Lynx repair - Part 5 - McWill LED screen mod installation

Power MOSFET and zener diodeWorks
RepairDifficulty: hardOpens caseBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

A shorted power MOSFET or zener feeds raw 9 V into the 5 V rails and can destroy the CPU. Replacing both is a preventive repair. Lynx I and II use the same replacement parts in different board locations.[3][4][6]

Parts

  • Replacement MOSFET and zener kit Fits — Same parts for Lynx I and II. Lynx I: Q11 and ZD1. Lynx II: Q12 and D13.[3]

Good to know

  • If the MOSFET or zener shorts, unregulated 9 V reaches the CPU and can fry it. The parts wear in the 9 V to 5 V switching circuit.[3]
  • Lynx II silkscreen: MOSFET Q12, zener D13. Lynx I: MOSFET Q11, zener ZD1, in different board positions. Same replacement parts for both.[3]
  • The DC jack is center-positive 9 V, 3.5 mm × 1.3 mm.[4]

⚠ Watch out

  • If the MOSFET or zener fails, 9 V can reach the CPU and ruin it. Replace both as a preventive repair.[3][6]

Guides:Replacing the MOSFET and Zener Diodes in an Atari Lynx

Sources (10)

SOURCES.TXT