Home › Devices › Canon › Canon HV20
CANON · CAMERA · 2007
Canon HV20
Also called: VIXIA HV20 · LEGRIA HV20 · iVIS HV20 · Canon Vixia HV20
2007 HDV miniDV camcorder with no LANC jack. Owners fit larger BP-2L / NB-2L packs and build wired or fiber IR remotes from the stock wireless controller. CHDK does not support this body.[1][9][2][7]
Which one do I have?
Specs
| Media | HDV / miniDV tape; miniSD for stills only (forum)[1][11] |
| Screen | 2.7-inch widescreen LCD, about 211,000 pixels[1] |
| Battery (stock) | BP-2L13 Li-ion, about 1200 mAh, 7.4 V; CA-570 power adapter[1][12][9] |
| Audio / video | 3.5 mm stereo mic jack; HDMI Type A (480i/480p/1080i); 10× optical zoom with lens-shift stabilizer[1] |
Mods (4)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Larger BP-2L / NB-2L batteryWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
Swap the stock BP-2L13 (~1200 mAh) for a Canon BP-2L14 (~1450 mAh) or a higher-capacity third-party NB-2L22-style pack. Plug-in only; no case work.[9][10][12][1]
Parts
- Canon BP-2L14 Fits with conditions — Manual lists BP-2L13, BP-2L14, and NB-2LH. One owner found the 2L14 less snug; others say it fits as well as the 2L13.[9]
- Third-party ~2200 mAh NB-2L22-style pack (e.g. Power2000) Fits with conditions — One 2007 test got about a third more runtime than stock. An engineer in the same thread warns that such packs may have leakage or heat issues and that the claimed capacity may be exaggerated.[10]
Good to know
- Stock pack is the BP-2L13, about 1200 mAh lithium-ion at 7.4 V.[1][12][9]
- Forum users treat the BP-2L14 as the larger Canon pack (about 1450 mAh) listed in the HV20 manual with BP-2L13 and NB-2LH.[9]
- A Power2000-style 2200 mAh pack tested at about a third more runtime than stock (idle play about 4:05 vs 3:09; live recording about 2:21–2:36 vs 1:55).[10]
⚠ Watch out
Guides:No guide found yet.
Wired IR remote from WL-D87Works
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
Rewire a Canon WL-D87 wireless remote so an IR LED on a cable sits over the camcorder's IR sensor. No wiring into the camera electronics. Gives cable control of the remote's own buttons only.[2][3][1]
Parts
- Canon WL-D87 wireless remote Fits — Opened and rewired; keep a second remote for practice. A mistake can destroy the remote.[2]
Good to know
- The HV20 has no LANC control jack.[2][1]
- The build rewires a standard WL-D87 remote for cable use. There are no electronic connections into the camera itself; the sender IR LED sits on the camera's IR sensor (e.g. with blu-tack).[2][3]
- The cable only gives the functions the remote already has. A plain hard-wired remote stays stuck to the camera on its cable; a panel-mount socket on the remote switches its own LED off only while the cable is plugged in.[2]
⚠ Watch out
- The builder warns that the Canon warranty is lost and that a wiring mistake can destroy the remote. Practice on a spare remote.[2]
Guides:How to make a "real" HV20 wired Lanc....How to make a "real" HV20 wired Lanc.... - Page 2
Optical (TOSLink) IR remote extensionWorks
Run the stock wireless remote's IR through a TOSLink or fiber cable to the camcorder's IR sensor. No soldering into the camera. Cheap tripod rigs and longer fiber builds (up to about 20 ft) are documented.[4][5][7][6]
Parts
- TOSLink or fiber-optic cable with adapters Fits — Aim the remote LED into the cable end. One builder used fiber up to about 20 feet with TOSLink and right-angle connectors.[4][7][5]
Good to know
- A TOSLink cable can carry the remote's IR to the camera sensor. Zoom and start/stop are the controls people care about most; the remote has no focus buttons.[4]
- A short TOSLink cable taped on a tripod with the remote on the handle works; the LED must aim almost directly into the cable.[5]
- A detailed HV20 fiber build uses fiber up to about 20 feet, TOSLink connectors, and adhesives; the author says the mods are reversible to stock.[7]
- Forum replies treat the optical cable, rigged right, as the wired substitute when a boom shot cannot aim the remote.[6]
Guides:IR Remote ModHV20 - No LANC? No problem.Cheap solution to missing LANC...
LCD flip / mirror switchExperimental
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Wire the internal LCD flip and mirror micro-switches to external switches for 35 mm depth-of-field adapters. Photos exist; the thread gives no step-by-step guide and says the camera is hard to take apart.[8]
Good to know
- One builder added a manual switch for LCD image flip and mirror by wiring two internal LCD micro-switches to switches on the top of the camera. It is a physical change, not a firmware hack.[8]
⚠ Watch out
- The thread shows photos only and says taking the HV20 apart is not easy. No install steps were published there.[8]
Guides:No guide found yet.
Sources (12)
- official VIXIA HV20 - Canon Camera Museum · 2026-11-17
- forum How to make a "real" HV20 wired Lanc.... · 2026-11-17
- forum How to make a "real" HV20 wired Lanc.... - Page 2 · 2026-11-17
- forum HV20 - No LANC? No problem. · 2026-11-17
- forum Cheap solution to missing LANC... · 2026-11-17
- forum Is there a LANC substitute for HV 20? · 2026-11-17
- forum IR Remote Mod · 2026-11-17
- forum HV20 lcd flip hack for the 35mm DOF adapters · 2026-11-17
- forum BP-2L14 doesn't fit as well as the HV20's included BP-2L13 battery.... · 2026-11-17
- forum 2200mAh Batteries by Power2000 · 2026-11-17
- forum miniSD video quality · 2026-11-17
- shop Canon BP-2L13 Rechargeable Battery - Camera Warehouse · 2026-11-17