★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000054devices tracked

Home › Devices › Canon › Canon PowerShot compacts

[ device photo ]NEW!

CANON · CAMERA

Canon PowerShot compacts

Also called: CHDK · Canon Hack Development Kit · PowerShot IXUS · PowerShot ELPH · PowerShot G · PowerShot SX

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 12 sources

A family of Canon DIGIC compact cameras that can run CHDK, an open-source add-on that loads from the SD card into RAM and does not replace Canon's firmware. It adds RAW photos, overlays, scripts, and a USB remote trigger. DIY infrared filter swaps are documented on some G and S bodies.[1][2][8][9]

3MODS
3WORK
0EXPERIMENTAL
12SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
PowerShot compactA, G, S, SX, IXUS and SD series—CHDK needs a build for the exact model and firmware version. Put ver.req or vers.req on the card root and press Set + Display in Playback to read that version. The platform tree lists many PowerShot and IXUS bodies.[3][5][7]

Mods (3)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

CHDK (Canon Hack Development Kit)Works
SoftwareDifficulty: easyCase stays closedNo solderingReversible

Open-source software that loads from a bootable SD card into RAM. It adds RAW photos, exposure tools, scripts, and USB remote triggering. Remove the card or unlock the write-protect tab to boot Canon's firmware alone.[1][2][3][4][5][6][7][10][11]

Parts

  • SD card prepared with CHDK Fits with conditions — Must match the camera model and firmware. Autoboot uses the write-protect lock tab after the card is marked bootable.[3][7]

Good to know

  • CHDK is an open-source firmware enhancement for DIGIC-based Canon cameras. It loads into RAM from the SD card and does not overwrite internal flash ROM.[1][2][4]
  • It adds RAW capture, a live histogram, zebra over/under indicators, and an intervalometer. Scripts run in uBASIC and Lua.[1][2]
  • The USB port can be used as a remote trigger input. CHDK senses a 5 V pulse on the USB line to fire the shutter via script.[2][10][11]
  • Install: extract the build onto an SD card with a card reader, confirm the firmware version with ver.req/vers.req, then load via the camera's firmware-update menu in Playback, or enable autoboot and slide the write-protect tab to locked.[3]
  • CHIMP (Canon Hack Installation and Management Platform) is a Windows tool that replaces older CHDK installers such as STICK. It needs Windows Vista SP2 or later and .NET Framework 4.6.[6]
  • The platform tree lists many PowerShot and Digital IXUS models (examples: IXUS 90 IS / SD790 IS, IXUS 40 / SD300, IXUS 70 / SD1000).[5]

⚠ Watch out

  • The build must match the exact model and firmware version.[3]
  • Autoboot needs the SD write-protect tab locked after the card is marked bootable. CHDK masks that lock so photos still save to the card.[3][7]

Guides:CHDK installation (2_installation.txt)CHDK intro (1_intro.txt)CHIMP README

Infrared conversionWorks
OpticsDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Stored charge Capacitors keep a dangerous charge after the device is off.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace the sensor's infrared-cut filter with infrared glass. Life Pixel documents DIY teardowns for the PowerShot S3 IS and G12.[8][9]

Parts

  • Infrared replacement filter Fits with conditions — Guides cover the PowerShot S3 IS and G12. Other bodies need a matching filter and teardown.[8][9]

Good to know

  • The conversion replaces the factory hot-mirror filter with custom infrared glass.[9]
  • The S3 IS guide opens the case, unsolders shielding, and lifts the sensor assembly.[8]
  • Removing the sensor needs careful handling so optical calibration stays intact.[9]

⚠ Watch out

  • Opening the camera voids the manufacturer's warranty.[8][9]
  • Internal work can present a high-voltage shock hazard.[8]

Guides:Canon PowerShot S3 IS DIY Infrared Conversion - Life PixelCanon PowerShot G12 DIY Infrared Conversion - Life Pixel

USB remote shutterWorks
ConnectivityDifficulty: mediumCase stays closedBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

With CHDK loaded, a 5 V pulse on the mini-USB port can trigger autofocus and shutter through a script. Builders use wired boxes, Arduino IR remotes, or Bluetooth adapters.[2][10][11][12]

Good to know

  • CHDK can sense a 5 V DC pulse on the USB port and fire the shutter via software scripting.[2][10]
  • An Arduino with an IR receiver can send those pulses for wireless infrared triggering on cameras without a native remote port.[11]
  • A Bluetooth module on the USB port plus a Lua script can trigger any CHDK-supported camera from a phone or laptop.[12]

Guides:Adding A Remote Shutter To A Cheap Digital CameraA Remote For CHDK Cameras Made Possible With ArduinoControlling A Point And Shoot With Bluetooth

Buttons & modes

BUTTONS.TXT
WhatHow
Boot factory firmwareRemove the SD card, or unlock it (slide the lock tab to unlocked), then turn the camera on.[4][3][7]
Read the firmware versionPut ver.req or vers.req on the SD card root. In Playback mode, press Set + Display.[3]
Autoboot CHDKAfter the card is marked bootable in the CHDK debug menu, remove it and slide the write-protect tab to locked, then turn the camera on.[3]

Sources (12)

SOURCES.TXT