★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000054devices tracked

Home › Devices › Casio › Casio F-91W

Casio F-91WNEW!

Photo: Ashley Pomeroy, CC BY-SA 3.0 · AI-edited (studio background)

CASIO · WATCH · 1989

Casio F-91W

Also called: F-91W · Module 593 · Casio Module 593

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 8 sources

A digital wristwatch from 1989 that runs on a CR2016 coin cell. The main mod, Sensor Watch, swaps the Module 593 board for one with USB firmware and a red and green backlight, and keeps the original case and display. Separate one-off builds add a contactless payment chip, a payment-card chip with its own antenna, an inverted display, or an oil-filled case.[1][2][4][5][8][7][6]

5MODS
1WORK
4EXPERIMENTAL
8SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Module 593F-91W1989Module 593 is stamped on the stainless steel caseback. The case is 38.2 mm by 35.2 mm by 8.5 mm, and the watch weighs 21 g. It shows the time, an auto calendar, a daily alarm, an hourly chime, and a 1/100-second stopwatch.[1]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Sensor Watch boardWorks
OtherDifficulty: mediumOpens caseReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Can brick A mistake can leave the device unable to start.

A drop-in board replaces the Module 593 PCB. It keeps the original case and display, adds a red and green backlight, and loads firmware over USB.[2][3][4][1]

Parts

  • Sensor Watch board (SAM L22) Fits — Replaces the Module 593 board. Keeps the original display and case.[2][4]
  • Piezo buzzer (optional) Fits with conditions — The board has pads to solder a buzzer. It is optional.[2]
  • Sensor on the 9-pin connector (optional) Fits with conditions — The connector breaks out 3 V, an I2C bus with pull-ups, and five GPIOs. The project suggests an environmental sensor, an accelerometer, or a magnetometer.[3]

Good to know

  • The board uses a Microchip SAM L22, a Cortex-M0+ that runs at 32 MHz, with 256 KB of flash and 32 KB of RAM.[2][4]
  • It drives the original ten-digit LCD and five indicator segments from the chip's built-in LCD controller.[2]
  • A red and green backlight, controlled by PWM, replaces the dim green corner LED.[2]
  • An on-board USB port and a double-tap UF2 bootloader let you drag firmware onto the watch. Firmware is written in C.[2]
  • The board connects to the three case buttons.[2]
  • It still runs on a CR2016. Battery life is about a year.[4]
  • The design keeps the original display and case.[4]

⚠ Watch out

  • Sensor Watch battery life is about a year on a CR2016. The stock module is rated for about 7 years on the same cell.[4][1]

Guides:Sensor-Watch - Joey Castillo

Contactless payment chipExperimental
ConnectivityDifficulty: expertOpens casePermanent

One build puts a 13.56 MHz payment chip inside the watch, with a printed front face and a pick-up coil around the outside.[5]

Good to know

  • A 13.56 MHz contactless payment chip sits inside the F-91W housing.[5]
  • An SLA-printed front face places the chip above the display, with a pick-up coil around the outside.[5]
  • The write-up covers matching the antenna to get good coupling near resonance.[5]

Guides:No guide found yet.

Passive smart card antennaExperimental
ConnectivityDifficulty: expertOpens casePermanent

A separate report adds a payment-card chip to the watch with a hand-built antenna tuned for the smaller watch face.[8]

Good to know

  • A hand-built antenna was tuned with a NanoVNA to match the original antenna's performance in the smaller watch face.[8]
  • The chip comes from a payment card and is powered over NFC by a reader.[8]

Guides:No guide found yet.

Inverted display and blue backlightExperimental
ScreenDifficulty: mediumOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

One report replaces the LCD polarizer so the digits are light on black, and replaces the faint green LED with blue LEDs.[7]

Good to know

  • The LCD is re-polarized with a different film so the digits are bright on a black background.[7]
  • A bright blue LED replaces the faint green one, and a second blue LED is added in parallel on the other side of the readout.[7]

Guides:No guide found yet.

Oil-filled caseExperimental
CaseDifficulty: expertOpens casePermanent

One report fills the case with oil so there is no air inside, then takes the watch nearly 5,000 meters down on an ROV.[6]

Good to know

  • The case is filled with oil to remove the air pockets. The watch survived a dive to 4,950 meters.[6]

Guides:No guide found yet.

Buttons & modes

BUTTONS.TXT
WhatHow
Sensor Watch firmware updateDouble-tap to start the UF2 bootloader, then drag the firmware file over USB.[2]

Sources (8)

SOURCES.TXT