★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000206devices tracked

Home › Devices › Casio › Casio W-800H

[ device photo ]NEW!

CASIO · WATCH

Casio W-800H

Also called: W-800H-1AV · W-800H-1BV · W-800H-1BVES · Casio W800H

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 8 sources · 1 item(s) unverified

Affordable digital Casio with a factory-disabled countdown timer. Opening a solder jumper on the module unlocks that mode. Opening the case risks water resistance.[1][2][6]

1MODS
1WORK
0EXPERIMENTAL
8SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
W-800H-1AVEuropean / Casio catalogue listing—Casio lists the W-800H-1AV on its European site. Same W-800H family as the 1BV / 1BVES colour codes.[5]
W-800H-1BVESBlack / blacked-out display, European export—Module 3240. Suffix 1BVES: colour 1 (black), B (blacked-out display), VES (export / European).[6]
W-800H-1BVBlackout dial (US listing)—Blackout-dial W800H-1BV sold in the US. One US shop lists countdown as a stock feature; other sources say it is off by default.[7] unverified
Specs
Module3240 (operation guide shared with module 3239)[6][4]
BatteryCR2025 lithium; about 10 years at stated alarm and backlight use[4][6]
Water resistance10 BAR / 100 m[6]
Accuracy±30 seconds a month at normal temperature[4]
BacklightLED with light guide panel[4]

Mods (1)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Unlock countdown timerWorks
SoftwareDifficulty: hardOpens caseFine solderingReversible30-60 min
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Remove the factory solder bridge on jumper 0 (Timer Disable) so the hidden countdown mode appears. No new firmware is installed.[1][2][3][6][8]

Special tools: #00 Phillips screwdriver, fine tweezers or X-Acto, fine soldering iron, solder wick

Good to know

  • Jumper 0 is labelled Timer Disable and is shorted at the factory; opening it (removing the solder) unlocks the countdown feature.[1][3][2]
  • Open means solder removed; shorted or closed means a blob of solder joins the pads.[1]
  • Steps: remove the battery, split the clamshell, set the jumpers, then reassemble. The original author did not clear memory and says the watch still worked.[1]
  • The W-800H does not receive new firmware during this modification.[3]
  • Other jumpers on the same board can change features: jumper 3 controls the 5× alarms (open by default), jumper 5 controls dual-time disable (open by default).[1]
  • Shop listings note the countdown is not on by default and that board-mod instructions exist.[6]

⚠ Watch out

  • Opening the case can damage the PCB, LCD connections, case seal or water resistance.[3][6]
  • Casio recommends only authorized technicians work on its watches when re-sealing and re-pressurizing are needed.[8]
  • Some jumpers may affect the piezo beeper; the original author noticed that only after writing up the mod.[1]
  • Board or module revisions may differ; check the jumper layout on your watch before soldering.[3][1]

Guides:Casio W-800H ExtrasModding a Casio W-800H With a Countdown TimerModding A Casio W800-H With A Countdown Timer | Hackaday

Sources (8)

SOURCES.TXT