Home › Devices › Nintendo › Game Boy Camera
NINTENDO · CAMERA · 1998
Game Boy Camera
Also called: Gameboy Camera
A 1998 Game Boy cartridge with a 180° swivel camera head. It stores about 30 pictures in battery-backed memory. The sensor is a Mitsubishi M64282FP that captures 128×128 and crops to 128×112 in four shades of gray. Photo! is homebrew firmware with manual exposure. A FRAM flash board can drop the save battery. The fixed lens can be swapped for CS-mount or Canon EF adapters.[8][7][1][2][4][5]
Which one do I have?
| Model | Variant | Year | How to tell |
|---|---|---|---|
| DMG-007 | Blue, Green, Red, Yellow, Clear Purple | 1998 | Cartridge with a camera head that swivels 180°. Works on original Game Boy hardware that takes Game Boy cartridges.[8] unverified |
Specs
Mods (5)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Photo! firmwareWorks
- ⚠ Can brick A mistake can leave the device unable to start.
- ⚠ Data loss Can erase what is on the device. Back up first.
Homebrew camera firmware with auto and full manual sensor control, custom dithering, and optional serial remote shutter from a second Game Boy. Needs a reflashable Game Boy Camera cart.[1]
Good to know
- Photo! needs a reflashable Game Boy Camera cart. Camera hardware modding is called out as advanced soldering.[1]
- Auto mode mimics stock exposure behavior. Manual mode lets you set exposure time, gain, sensor voltage out, and edge enhancement.[1]
- A dithering menu offers custom patterns. The save format stays compatible with stock Game Boy Camera saves, so you can switch firmware without losing pictures.[1]
- A remote-control program on a second flashable cart can drive the shutter over the serial link cable.[1]
- Builds also exist for Mega Duck (Cougar Boy) and Sega Game Gear with cartridge-slot adapters.[1]
Guides:GitHub - untoxa/gb-photo
Dump pictures over the link cableWorks
- ⚠ Data loss Can erase what is on the device. Back up first.
An Arduino (or similar) pretends to be the Game Boy Printer on the link cable and pulls pictures off as files, so a dying save battery does not wipe them.[6][7]
Good to know
CS-mount lens adapterWorks
Replace the front half of the swivel eyeball with a 3D-printed CS-mount ring so you can fit CCTV zoom lenses and similar glass. The stock plastic lens is roughly 41 mm full-frame equivalent and fixed.[4]
Parts
- 3D-printed CS-mount ring (Herr_Zatacke) Fits — Replaces half of the eyeball; screwed back to the original white piece. Takes CS-mount lenses.[4]
Good to know
Canon EF lens mountExperimental
A 3D-printed Canon EF bayonet screws onto the camera after light disassembly so full-size EF glass can reach the sensor.[5]
Parts
- 3D-printed Canon EF mount Fits — Designed in Rhino 3D; screws onto the Game Boy Camera after light disassembly.[5]
Good to know
- Bastiaan’s printed EF mount lets large EF lenses (example: 70–200 f/4 with a 1.4× extender) sit at a usable flange distance on the Game Boy Camera.[5]
FRAM flash boardWorks
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Data loss Can erase what is on the device. Back up first.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
- ⚠ Check the law May break a law or rule where you live.
Open-source replacement PCB with FRAM (no save battery) and 2×1 MB flash banks. It reuses parts harvested from an original Game Boy Camera cartridge, including the MAC-GBD chip.[2][3][1]
Parts
- Game Boy Camera flashcart (2×1 MB flash, FRAM) Fits with conditions — BOM harvests U1 (MAC-GBD) and diode D2 from a donor Game Boy Camera cartridge; the sensor connector can be harvested or bought.[2]
Good to know
- FRAM replaces battery-backed SRAM so pictures are not lost when a coin cell dies.[2]
- 2 MB of flash is split into two 1 MB banks, so you can keep more than one firmware image on the cart.[2]
- The board reuses parts of an original camera: harvest MAC-GBD (U1) and diode D2 from a donor cartridge. The B9B-ZR connector can be harvested or bought.[2]
- Design files are on GitHub (HDR/Gameboy-Camera-Flashcart) and shared on PCBWay.[3][2]
⚠ Watch out
- Building it means harvesting chips from a donor Game Boy Camera cartridge.[2]
Guides:Game Boy Camera Flashcart | 2x1MB | FRAMGitHub - HDR/Gameboy-Camera-Flashcart
Sources (8)
- docs GitHub - untoxa/gb-photo · 2026-11-14
- blog Game Boy Camera Flashcart | 2x1MB | FRAM · 2026-11-14
- official GitHub - HDR/Gameboy-Camera-Flashcart · 2026-11-16
- blog Gameboy Camera : lens mod – Sébastien Tourneux · 2026-11-14
- blog A Canon Lens Adapter For The Game Boy Camera · 2026-11-16
- blog Arduino Saves Game Boy Camera · 2026-11-16
- blog Taking Amazing Pictures With A GameBoy Camera! · 2026-11-14
- wiki Game Boy Camera - Wikipedia · 2026-11-14