★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000206devices tracked

Home › Devices › Garmin › Garmin eTrex

[ device photo ]NEW!

GARMIN · OTHER · 2011-2018

Garmin eTrex

Also called: eTrex 10 · eTrex 20 · eTrex 30 · eTrex 22x · eTrex 32x

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 12 sources · 2 item(s) unverified

Rugged AA-powered handheld GPS line. Common tweaks are a startup.txt splash message, a glued joystick guard, and a soldered 10K auto-power-on resistor for embedded installs. Case construction differs by generation.[1][3][4][6]

6MODS
5WORK
0EXPERIMENTAL
12SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
eTrex 10Monochrome, no card slot—Monochrome 128×160 screen, 8 MB internal, no compass or altimeter, no microSD slot.[2][6]
eTrex 20 / 20x / 30 / 30xColour family with optional microSD—Garmin groups these in one manual. eTrex 30: 65K colour 176×220, microSD, two AA, cannot charge batteries; runs from mini-B USB power when plugged in.[6][1][7]
eTrex 22x / 32xLater colour units with screwed case—Same microSD holder design as the 20x/30x line. The iFixit 22X joystick guide uses six 11 mm TR6 case screws, unlike older screwless eTrex shells.[8][10][9]
Specs
PowerTwo AA cells; eTrex 30 rated about 25 hours and cannot charge cells over USB[1][2]
Display (eTrex 10)Transflective monochrome, 128×160[2]
Display (eTrex 30)Transflective 65K colour TFT, 176×220[1]
Storage (eTrex 10)8 MB internal; no card slot[2]
Storage (eTrex 30)Internal plus microSD for maps[1][7]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Custom startup messageWorks
SoftwareDifficulty: easyCase stays closedNo solderingReversible
  • ⚠ Data loss Can erase what is on the device. Back up first.

Edit startup.txt in the Garmin folder to show a short splash message and set how long it displays.[1][12]

Good to know

  • On the eTrex 30, startup.txt in the Garmin folder ships with no message and display time zero; editing it adds a message and a display time.[1]
  • On Oregon units the same file supports up to five lines (about 30 characters each) and should be saved as UTF-8 for non-English text; boot time grows by the display duration.[12]

⚠ Watch out

  • Use at your own risk; problems have been reported.[1]

Guides:Garmin/eTrex 30 - OpenStreetMap Wiki

microSD map cardWorks
StorageDifficulty: easyCase stays closedNo solderingReversible5 min
  • ⚠ Data loss Can erase what is on the device. Back up first.

Install a microSD card under the battery cover for extra maps or storage. Not available on every eTrex (the eTrex 10 has no slot).[7][8][1][11]

Good to know

  • Garmin's steps: turn the D-ring counter-clockwise, remove the cover and battery, slide the holder, insert the card with gold contacts down.[7][8]
  • The feature is not available on every model in that manual family.[7]
  • Maps on the eTrex 30 can sit in internal storage or on the SD card.[1]
  • One eTrex 30x owner fixed a card that would not show maps by swapping to a different microSD.[11] unverified

⚠ Watch out

  • Do not use a sharp object to remove the batteries.[7]

Guides:eTrex 10/20/20x/30/30x - Installing a Memory Card

Joystick protector ringWorks
Buttons & inputDifficulty: easyCase stays closedNo solderingPermanent30 min
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Glue a short ring around the rocker so clothing bumps do not shift the map. Field build from a wire-nut end.[4]

Good to know

  • Author cut a protector ring from a wire nut (about 4 mm tall, 13 mm inner diameter) and glued it on with two-part plastic adhesive.[4]
  • Surfaces were roughened and cleaned; the joystick was masked before gluing. Height can be filed down.[4]

⚠ Watch out

  • The glue is permanent.[4]

Guides:Garmin Etrex Fiddle Fix - The Backcountry Ski Site

3 V DC auto power-onWorks
ChargingDifficulty: hardOpens caseFine solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Solder a 10K ohm resistor between ON1 and ON2 so the unit powers on when external 3 V is applied. Meant for embedded or vehicle installs.[3][10]

Parts

  • 10K ohm resistor Fits with conditions — Fits between pads marked ON1 and ON2 on the display side of the PCB near the power button.[3]

Good to know

  • The mod is one 10K ohm resistor between pads ON1 and ON2 on the display side of the board near the power button.[3]
  • The unit can still be turned off with the power button or by removing external power.[3]
  • EOSS unit case has no screws: remove the rubber grip, pry the case, unplug the battery-compartment cable, lift the board.[3]

⚠ Watch out

  • Install the resistor carefully on the small pads. Newer 22X units use six case screws; confirm your shell before following the screwless steps.[3][10]

Guides:Garmin eTrex Auto-Power Up Mod | Edge of Space Sciences

Joystick replacement (22X)Works
RepairDifficulty: mediumOpens caseNo solderingReversible

Replace the rocker on an eTrex 22X: TR6 case screws, T4 motherboard screw, then pry the assembly free.[10]

Special tools: TR6 screwdriver, T4 screwdriver, plastic pry bar

Good to know

  • Remove six 11 mm case screws with a TR6 driver after turning the battery D-ring, then remove the battery housing.[10]
  • One 5 mm T4 screw holds the motherboard; pry the indicated area with a plastic pry bar to free the joystick.[10]

⚠ Watch out

  • Guide is for the eTrex 22X, not the eTrex 10/20/30.[10]

Guides:Garmin eTrex 22X Joystick Replacement - iFixit

Hacked firmware (historical)Discontinued
SoftwareDifficulty: expertCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.

A 2002 post mentions community firmwares with extra map symbols and DIY firmware kits. A failed flash can brick the unit.[5]

Good to know

  • 2002 write-up says hacked firmwares existed that add features such as new map symbols, and that kits existed to make your own changes.[5]
  • The same post warns a failed flash can leave the unit a worthless pile of plastic.[5]

Guides:No guide found yet.

Sources (12)

SOURCES.TXT