★ 208 device pages approved★ 2530 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 208 device pages approved★ 2530 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000214devices tracked

Home › Devices › Hewlett-Packard › HP 200LX

[ device photo ]NEW!

HEWLETT-PACKARD · PDA · 1994-1999

HP 200LX

Also called: 200LX · HP 200LX Palmtop PC · Project Felix · F1060A · F1061A · F1216A

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 15 sources · 5 item(s) unverified

A DOS palmtop PC from 1994, sold as F1060A, F1061A, and F1216A, with MS-DOS 5.0 in ROM.[1]

7MODS
6WORK
1EXPERIMENTAL
15SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
F1060A200LX—One of the three 200LX product numbers, sold in 1, 2, and 4 MB versions.[1]
F1061A200LX—One of the three 200LX product numbers, sold in 1, 2, and 4 MB versions.[1]
F1216A200LX—One of the three 200LX product numbers, sold in 1, 2, and 4 MB versions.[1]
Specs
IntroducedAugust 1994 for the 1 MB and 2 MB models. February 1997 for the 4 MB model. HP stopped the 200LX in December 1999.[4]
Screen4.8-inch, 640×200 monochrome STN, 4 grey levels[4]
CPUHornet, 7.91 MHz[1]
Memory1, 2, or 4 MB factory. MS-DOS 5.0 in ROM.[1]
DOS limit640 KB of system RAM. Extra memory is storage.[8]
PowerTwo AA cells and a CR2032 backup cell[1]
Card slotOne PCMCIA slot: a modem or a memory card, not both[2]
SerialFull serial port on a proprietary mini connector[1]
Infrared and soundInfrared is SIR, not IrDA. Sound is a piezo PC speaker.[4]

Mods (7)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

AA cells and backup coin cellWorks
BatteryDifficulty: easyCase stays closedNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Data loss Can erase what is on the device. Back up first.

The palmtop runs on two AA cells, alkaline or NiCd. Newer NiMH cells can charge in the unit if the battery type is set to NiCad. A CR2032 keeps the RAM drive alive when the AA cells are out.[2][3][1][13]

Good to know

  • The 200LX uses two AA cells, alkaline or NiCd. Newer NiMH cells recharge in the palmtop when the type is set to NiCad. Older rechargeable alkaline or NiMH cells need an external charger.[2]
  • A 1998 FAQ recommends Times2 Tech 1300 mAh NiMH cells.[2]
  • The backup cell is a CR2032. Hewlett-Packard suggests replacing it every year. It holds the RAM drive when the main cells are empty.[3]

⚠ Watch out

  • If the AA cells are fully drained or removed, Backup Mode can erase the RAM drive. Turn the palmtop off before you insert a PC Card.[3]
  • One FAQ says the adapter is 12 V DC, negative tip, up to 750 mA, about a 5.5 mm barrel. A positive tip, or AC instead of DC, can destroy the adapter jack.[2]
  • Another hardware page says the palmtop adapters all output 9 V AC. Do not mix those two descriptions.[13]

Guides:No guide found yet.

Format a memory cardWorks
StorageDifficulty: mediumCase stays closedNo solderingReversible
  • ⚠ Data loss Can erase what is on the device. Back up first.

SRAM and flash cards share the one PCMCIA slot with a modem. A reformat with 1 KB clusters makes the card usable. Anything past 64 MB is ignored.[14][2][1]

Good to know

  • The slot holds a modem or a SRAM or flash card, not both at once.[2]
  • Format on Windows 9x with a 1 KB cluster. A larger card only shows its first 64 MB. Windows XP makes the card unusable in the 200LX.[14]
  • With a third-party driver, removable cards are listed up to 2 GB.[1]
  • If a format goes wrong, the card can be reformatted from the palmtop's own DOS tools.[14]

Guides:Re-formatting an HP 200LX card

Headphone jackWorks
AudioDifficulty: mediumOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Add a 3/32-inch jack wired to the battery-contact springs, so the piezo speaker sound comes out of headphones. The case needs a hole, and thick wire makes the palmtop bulge.[11][12]

Special tools: Torx T6 screwdriver

Parts

  • 3/32-inch open-style headphone jack Fits — Wired to the springs that touch the motherboard, along the battery clip. Use thin wire, about 30 gauge. There is no volume control unless the headphones have one.[11]

⚠ Watch out

  • Take the AA cells and the CR2032 out first. The RAM drive is cleared. Opening the case voids the HP warranty. Four Torx T6 screws sit under the rubber feet.[12]
  • Wire that is too thick makes the case bulge and rock on a desk. You may have to trim plastic inside.[11]

Guides:Fitting an external speaker jackA palmtop adventure

Electroluminescent backlightWorks
ScreenDifficulty: hardOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

A DIY kit swaps the reflective foil behind the LCD for an EL foil and a driver. The screen is less crisp and the batteries last about half as long with the light always on. An LED lamp is the easier option.[10][2][12]

Special tools: Torx T6 screwdriver

Good to know

  • The kit is an EL foil plus a driver module. You take the palmtop apart, including the screen module. The kit does not include tools. Replacement screens are very hard to get.[10]
  • With the light always on, battery life drops by about half. That was measured on a 2 MB single-speed unit and a 32 MB double-speed unit. The EL foil is less crisp than the original reflector.[10]
  • A 1998 FAQ said no commercial backlight existed yet.[2]
  • A later write-up says the only route is a DIY kit, and that an LED light is much easier to fit.[10]
  • The OmniGo 700LX uses the same screen module in a different case.[10]

⚠ Watch out

  • Take the AA cells and the CR2032 out first. The RAM drive is cleared, and the HP warranty is void. Four Torx T6 screws sit under the rubber feet.[12]

Guides:No guide found yet.

Double-speed crystalWorks
OtherDifficulty: hardOpens caseBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Replace the 15.8 MHz crystal with one at twice that frequency, then load a driver so the screen, clock, and serial port stay in step. HP saw more failures on double-speed units.[5][6][9][12]

Special tools: soldering iron, Torx T6 screwdriver

Parts

  • 32 MHz crystal and driver card Fits — The original 15.8 MHz crystal is unsoldered and a 32 MHz crystal is soldered in. A driver has to correct the screen, the clock, and the serial port.[9] Buy: 200lx.net

Good to know

  • The stock crystal is 15.836774 MHz. A crystal at exactly twice that frequency is the double-speed part. Without a driver the screen shifts, the clock runs twice as fast, and the serial port runs at double speed.[5]
  • A plain 32 MHz crystal can run with the CU32.COM driver, but 57 kbps and 115 kbps serial do not work at that frequency.[5]

⚠ Watch out

  • HP said double-speed units failed more often than stock units. The change voids the HP warranty.[6]
  • Take the AA cells and the CR2032 out first. The RAM drive is cleared. Four Torx T6 screws sit under the rubber feet.[12]

Guides:Making the palmtop faster, brighter and better200LX upgrades

More internal RAMWorks
StorageDifficulty: mediumOpens caseNo solderingReversible
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

After-market boards raise the RAM above the factory 1, 2, or 4 MB. A motherboard swap uses a Torx T6 driver. DOS still only sees 640 KB as system memory.[1][4][7][5][8][9][12]

Special tools: Torx T6 screwdriver

Parts

  • 200LX motherboard with more RAM Fits — Sold as a board swap. The only tool named for the swap is a Torx T6 driver.[9] Buy: 200lx.net

Good to know

  • Factory RAM is 1, 2, or 4 MB. After-market updates are described up to 64 MB.[1]
  • A fan page says memory upgrades up to 128 MB have been reported.[4] unverified
  • A 4 MB add-on takes a 1 MB or 2 MB palmtop to 5 MB. It is not HP-approved. On a repair, HP might put the standard 1 MB or 2 MB back.[7]
  • One article says a 4 MB board replaces the 1 MB daughterboard on the 2 MB model, and that the connector can be missing.[5] unverified
  • In the 1990s, memory and speed work was also done by mailing the palmtop to Thaddeus Computing. System RAM stays at 640 KB. Extra memory is storage.[8]

⚠ Watch out

  • The 4 MB upgrade voids the HP warranty.[7]
  • Take the AA cells and the CR2032 out first. The RAM drive is cleared. Four Torx T6 screws sit under the rubber feet.[12]

Guides:No guide found yet.

Use the keyboard as a USB keyboardExperimental
Buttons & inputDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Data loss Can erase what is on the device. Back up first.

One maker turned a dead 200LX keyboard into a USB keyboard with a Teensy 2.0 and a small interposer. The flex pads are an odd pitch. Do not take apart a working palmtop for this.[15]

Good to know

  • The build uses a Teensy 2.0 and kbfirmware.com. Each trace on the keyboard flex had to be probed because the pad spacing is unusual. The donor already had a dead LCD and motherboard.[15] unverified

⚠ Watch out

  • The maker asks people not to scrap a working 200LX. This donor was already broken.[15] unverified

Guides:No guide found yet.

Sources (15)

SOURCES.TXT