Home › Devices › Apple › iPod nano (1st generation)
APPLE · MUSIC PLAYER · 2005
iPod nano (1st generation)
Also called: nano 1G · iPod nano 1st gen · A1137
September 2005 flash nano (1/2/4 GB) in black or white. Storage is soldered — no flash adapter. Practical mods are a soldered battery swap, display and click-wheel repair, headphone jack work, and Rockbox.[5][4][8][2]
Which one do I have?
Specs
| Screen | 1.5-inch, 132×176[4] |
| Storage | 1 GB, 2 GB, or 4 GB soldered flash (not upgradable)[5][4][1] |
| Battery | Internal lithium-ion; original about 3.7 V / 340 mAh (community figure); soldered to the board[4][14][8] |
| Ports | 30-pin dock connector (USB 2.0; FireWire for charging only), 3.5 mm headphone jack[1][4][5] |
| Stock firmware | 1.3.1[4] |
Mods (5)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Rockbox custom firmwareWorks
- ⚠ Can brick A mistake can leave the device unable to start.
- ⚠ Data loss Can erase what is on the device. Back up first.
Free open-source firmware with a custom bootloader so you can dual-boot Rockbox and the stock iPod OS.[2][3][12][13][14]
Good to know
- Rockbox TargetStatus lists iPod Nano among stable targets with a released bootloader and Rockbox Utility support.[2]
- A 2011 Cult of Mac guide installs Rockbox via Rockbox Utility on a 1st gen 1 GB nano running firmware 1.3.1, with a custom bootloader for dual boot.[12]
- The nano must appear as a USB disk drive before install. One walkthrough formats it to FAT32 first.[13]
- Linux install notes mention an old Rockbox Utility binary and finishing with a hard reset (hold Menu and Select).[14] unverified
⚠ Watch out
Guides:Renew Your Old iPod Nano With Some Software Mods [How-To] | Cult of MacMy Notepad: February 2011 (Rockbox on Nano 1G)
Soldered battery replacementWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
Open the eleven-clip rear panel and desolder the three battery leads to fit a new cell. Very hard; needs fine soldering near a lithium pack.[8][11][1][15][16][14]
Special tools: soldering iron, spudger
Good to know
- iFixit rates the swap Very difficult (40 minutes to 2 hours). The battery stays tied to the board by three wires until you desolder them.[8]
- The rear panel is held by eleven clips. Limit heat on the logic board while desoldering and soldering.[8]
- If the nano will no longer charge after a full charge attempt, the battery must be replaced — and that requires soldering.[11]
- Community notes list the original pack at 3.7 V / 340 mAh; a thicker 400 mAh cell can still fit.[14] unverified
- Wikipedia notes the nano battery is soldered to the main board, so swaps need soldering tools.[1]
⚠ Watch out
- Apple warned that 1st gen nano batteries may overheat and pose a safety risk. Affected units were sold September 2005–December 2006; risk rises as the cell ages. Stop using a swollen or hot unit.[15][16][1]
- Apple ran a free replacement program in 2011. Eligibility and claim forms from that era may no longer apply.[15][16]
Guides:iPod Nano 1st Generation Battery Replacement - iFixit
Display replacementWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
Replace a cracked or dead colour display. Shares the case opening with the battery guide; the panel is held by edge adhesive.[9]
Good to know
- iFixit rates display replacement Difficult (30 minutes to 2 hours). Pry the adhesive holding the display edge with a spudger.[9]
Guides:iPod Nano 1st Generation Display Replacement - iFixit
Click wheel replacementWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
Replace a dead or sticky click wheel. Free the orange ribbon by flipping its black tab with a spudger.[10]
Good to know
- iFixit rates the click-wheel swap Difficult. Flip up the black plastic tab holding the orange ribbon, then free the wheel.[10]
- Parts exist for black and white 1st gen click wheels.[10]
Guides:iPod Nano 1st Generation Click Wheel Replacement - iFixit
Headphone jack replacementWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
Desolder and replace a defective headphone jack. One 2009 write-up follows the iFixit open, then swaps the jack with iron and braid.[17]
Special tools: soldering iron, solder braid
Good to know
Sources (17)
- wiki iPod - Wikipedia · 2026-11-16
- wiki TargetStatus – Rockbox · 2026-11-16
- wiki Rockbox - Wikipedia · 2026-11-16
- wiki iPod Nano - Wikipedia · 2026-11-16
- official Identify your iPod model - Apple Support · 2026-11-16
- docs All iPod nano By Model Number - EveryiPod.com · 2026-11-16
- wiki Models/iPod - The Apple Wiki · 2026-11-16
- docs iPod Nano 1st Generation Battery Replacement - iFixit · 2026-11-16
- docs iPod Nano 1st Generation Display Replacement - iFixit · 2026-11-16
- docs iPod Nano 1st Generation Click Wheel Replacement - iFixit · 2026-11-16
- wiki iPod Nano 1st Generation Troubleshooting - iFixit · 2026-11-16
- news Renew Your Old iPod Nano With Some Software Mods [How-To] | Cult of Mac · 2026-11-16
- blog My Notepad: February 2011 (Rockbox on Nano 1G) · 2026-11-16
- wiki Rockbox on Ipod Nano - Modding Fridays · 2026-11-16
- news Apple is replacing first gen iPod nanos due to faulty batteries · 2026-11-16
- news Apple Launches Worldwide Replacement Program for First-Generation iPod Nano - MacRumors · 2026-11-16
- blog Replacing a 1st Gen iPod Nano headphone jack · 2026-11-16