★ 155 device pages approved★ 1835 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 155 device pages approved★ 1835 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000161devices tracked

Home › Devices › Apple › iPod nano (3rd generation)

[ device photo ]NEW!

APPLE · MUSIC PLAYER · 2007-2008

iPod nano (3rd generation)

Also called: nano 3G · fat nano · A1236 · iPod nano 3rd gen

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 13 sources · 1 item(s) unverified

September 2007 "fat" nano (4 or 8 GB soldered flash) with a wider 2-inch screen and video. Storage adapters do not fit. Practical mods are a soldered battery swap, display and rear-panel repair. Rockbox for this model is still an unstable development port.[1][2][4][11]

5MODS
3WORK
1EXPERIMENTAL
13SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
A12363rd generation (4 GB / 8 GB)2007Wider "fat" body, hold switch on the bottom, plays video. Serial tail codes include YOP, YOR, YXR, YXT, YXV, YXX. Anodized aluminium front, chromed stainless back. Discontinued September 2008.[1][2][3]
Specs
Screen2-inch colour LCD, 320×240, blue-white LED backlight[2]
Storage4 GB or 8 GB soldered flash (not upgradable with adapters)[2][1][12]
BatteryLithium-ion; replacement cells listed at 370 mAh (616-0337) or 450 mAh[2][9][10]
Ports30-pin dock (USB sync/charge; FireWire charge only); video out via dock only[2]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Soldered battery replacementWorks
BatteryDifficulty: expertOpens caseFine solderingPermanent1-2 hours
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Open the eight-clip rear panel, desolder three battery leads through the logic board, and solder in a new cell. Very hard; heat can damage the board.[4][7][9][10][3]

Special tools: soldering iron, desoldering braid, lead-free solder, pry tool

Parts

  • iPod nano (3rd Gen) battery 616-0337 (370 mAh) Fits — Requires soldering to the logic board.[9] Buy: ifixit.com
  • NewerTech NuPower 450 mAh battery Fits with conditions — Shop lists it for the 3rd gen; install is still the soldered iFixit procedure. Higher capacity vs 370 mAh is a listing claim.[10][4] Buy: eshop.macsales.com

Good to know

  • iFixit rates the swap Very difficult (1–2 hours). Battery leads pass through holes in the logic board and are held by solder.[4]
  • The rear panel has eight clips. Limit heat on the logic board while desoldering and soldering.[4]
  • A shop guide shows the cell glued in place, then soldered at three points on the motherboard.[7]
  • EveryMac says battery replacement on all nano generations is difficult, needs soldering, and recommends professional install. Apple no longer offers paid nano battery service.[3]

Guides:iPod Nano 3rd Generation Battery Replacement - iFixitiPod Nano 3rd Generation Battery Repair Replacement Guide – Repairs Universe

Display replacementWorks
ScreenDifficulty: hardOpens caseNo solderingPermanent
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace a cracked or dead 2-inch LCD. The glass is thin and held by perimeter adhesive; unplug the click-wheel and display ribbons first.[5][8]

Good to know

  • The guide starts with the rear panel, and removing it causes considerable damage to that panel, so have a spare ready.[5]
  • iFixit rates display replacement Difficult. Adhesive around the perimeter holds the panel; pry carefully — the thin glass cracks easily.[5]
  • Slide the display ribbon out of its socket before lifting the panel. Click-wheel ribbon is unplugged in the same teardown path.[5]

Guides:iPod Nano 3rd Generation Display Replacement - iFixitiPod Nano 3rd Generation LCD Screen Repair Replacement Guide – Repairs Universe

Rear panel replacementWorks
CaseDifficulty: mediumOpens caseNo solderingPermanent10-30 min
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Remove the chromed stainless rear panel (eight clips). Removal usually ruins the old panel, so plan on a spare for reassembly.[6]

Good to know

  • iFixit rates rear-panel removal Moderate (10–30 minutes). Eight clips lock onto tabs on the front case.[6]
  • Removing the rear panel causes considerable damage to that panel. Buy a spare rear panel before you open it.[6]

⚠ Watch out

  • Keep metal pry-tool edges toward the rear panel so you do not scratch the anodized front case.[6]

Guides:iPod Nano 3rd Generation Rear Panel Replacement - iFixit

Rockbox (unstable port)Experimental
SoftwareDifficulty: hardCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Rockbox lists Nano 3G as an unstable development target with incomplete driver support.[11]

Good to know

  • Rockbox TargetStatus lists iPod Nano 3G among unstable development targets.[11]

Guides:No guide found yet.

Flash storage upgradeNot possible
StorageDifficulty: noneCase stays closedNo solderingReversible

Soldered NAND flash — no storage adapter route like classic hard-drive iPods.[2][12][13]

Good to know

  • The 3rd gen nano uses 4 GB or 8 GB of flash memory soldered on the board.[2][12]
  • iFlash adapters are made for hard-drive iPods such as the Video, Classic and Photo, not for soldered nano flash.[13]

Sources (13)

SOURCES.TXT