★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000206devices tracked

Home › Devices › Apple › iPod touch 1st gen

[ device photo ]NEW!

APPLE · MUSIC PLAYER · 2007-2008

iPod touch 1st gen

Also called: iPod touch 1G · A1213 · iPod1,1 · N45AP

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 16 sources · 1 item(s) unverified

First iPod touch (A1213) with a soldered battery. Repairs cover battery, display and panels. Jailbreak tools such as redsn0w target up to iPhone OS 3.1.3. No storage adapter is listed for it.[5][1][13][16]

6MODS
4WORK
1EXPERIMENTAL
16SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearFirmwareHow to tell
A12138 GB20073.1.3Model A1213 / iPod1,1. Flat back without the 2nd gen's oval antenna cover. Order MA623LL/A for 8 GB.[5][6][8]
A121316 GB20073.1.3Same A1213; order MA627LL/A.[6][5]
A121332 GB20083.1.332 GB added February 2008. Same model number.[6][5]
Specs
Screen3.5-inch Multi-Touch widescreen[5]
Storage8, 16 or 32 GB NAND flash[7]
BatteryAbout 580 mAh / 2.15 Wh. Music ~22 h, video ~5 h[7][6]
Max OSiPhone OS 3.1.3[6][10]
RadiosWi-Fi 802.11b/g; no built-in Bluetooth[6][15]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Replace the batteryWorks
BatteryDifficulty: expertOpens caseFine solderingReversible30 min-2 hours
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Open the case, free the glued cell from the display, and desolder/resolder the battery leads on the board.[1]

Special tools: Soldering iron

Good to know

  • iFixit rates the guide Very difficult. The battery is glued to the display with no screws holding it.[1]
  • Old leads are desoldered and new leads soldered to the board pads (black, white, red order in the guide).[1]

⚠ Watch out

  • Opening the case is called a tough and potentially dangerous task. The small underside of the logic board is very bendable and frail.[1]

Guides:iPod Touch 1st Generation Battery Replacement - iFixit

Replace the displayWorks
ScreenDifficulty: hardOpens caseNo solderingReversible

Open the case, lift the antenna assembly, and swap the display.[2]

Good to know

  • iFixit rates the display guide Difficult. Antenna loop board and two-board antenna assembly come out; the antenna is glued down.[2]

⚠ Watch out

  • The gold antenna can fall out of its housing and must be seated before closing.[2]

Guides:iPod Touch 1st Generation Display Replacement - iFixit

Replace the back panelWorks
CaseDifficulty: hardOpens caseNo solderingReversible10-30 min

Separate front and back and swap the rear shell.[3]

Good to know

  • iFixit rates the back-panel guide Difficult, 10–30 minutes. Parts are listed for 8, 16 and 32 GB labels.[3]

Guides:iPod Touch 1st Generation Back Panel Replacement - iFixit

Replace the front panel assemblyWorks
CaseDifficulty: hardOpens caseNo solderingReversible

Swap the front glass and bezel assembly. Community guide; same teardown path as the display guide.[4]

Good to know

  • Community-contributed iFixit guide for the front panel assembly, rated Difficult.[4]

Guides:iPod Touch 1st Generation Front Panel Assembly Replacement - iFixit

Jailbreak (redsn0w / PwnageTool)Experimental
SoftwareDifficulty: hardCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Older tools jailbreak up to iPhone OS 3.1.3. Common path: restore to 3.1.3, then run redsn0w pointed at a 3.1.2 IPSW.[8][13][14][11][12][9]

Good to know

  • PwnageTool covers 1.1.4 through 3.1.3, and redsn0w 0.9.4 and Spirit cover 3.1.3.[8]
  • On a Mac: restore to 3.1.3, point redsn0w at the 3.1.2 firmware file, enter DFU by holding Home and Power for 10 seconds.[13]
  • On Windows, redsn0w 0.9.4 supports the iPod Touch 1G (and 2G non-MC) on 3.1.3, with the same 3.1.2 IPSW step.[14]
  • redsn0w is not compatible with the old 1.x firmwares; update first.[11]

⚠ Watch out

  • A 2008 TechCrunch attempt on a 16 GB unit bricked the device mid-process.[12]

Guides:How to Jailbreak Your iPod Touch 1G Using RedSn0w (Mac) [3.1.3] - iClarifiedHow to Jailbreak iPhone 3.1.3 and iPod Touch 3.1.3 with redsn0w 0.9.4

Flash storage upgradeNot possible
StorageDifficulty: expertOpens caseFine soldering

Not possible with adapter boards. No storage adapter is listed for the touch.[16][7]

Good to know

  • iFlash lists its adapters only for iPod Video, Classic and Photo models; the touch is not among them.[16]

Sources (16)

SOURCES.TXT