★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000206devices tracked

Home › Devices › Kodak › Kodak Brownie (box camera)

[ device photo ]NEW!

KODAK · CAMERA · 1900-1986

Kodak Brownie (box camera)

Also called: Brownie · Box Brownie · Kodak Brownie Hawkeye · Six-20 Brownie · Brownie Model 1

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 11 sources · 3 item(s) unverified

Eastman Kodak’s long box-camera line. Common mods reuse the shell for digital builds, convert a Six-20 to pinhole, or flip the Hawkeye meniscus lens for soft focus.[5][1][6][9]

6MODS
3WORK
3EXPERIMENTAL
11SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Brownie (first / Model 1)Cardboard box, No. 117 film1900Basic cardboard box camera on No. 117 roll film. One ESP32 digital build used a scrapped Brownie Model 1 body.[5][1]
Brownie No. 2Models A–F1901-1935First Brownie to use 120 film. Made in five models, A to F.[5]
Six-20 Brownie620 box, including model E—Sticker warns to use 620 roll film, not 120. Model E used in a reversible Bluetooth HID shutter build; plain Six-20 used for a pinhole conversion.[6][8][10]
Brownie HawkeyeBakelite, 620 film1949Bakelite body, 620 film. Lens flip and one Raspberry Pi digital build use this model.[9][7]
No. 2 Autographic BrownieAutographic—Autographic Brownie used in a Raspberry Pi Zero 2W digital conversion that keeps the original mechanism.[4]
Specs
Film (early No. 2)120 roll film (Brownie No. 2, 1901–1935)[5]
Film (Six-20)620 roll film (same film stock as 120; respool onto 620 spindles)[6][3]
ESP32-CAM sensorOV2640 2 MP; module standby about 80 mA without streaming[1][11]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Flipped meniscus lens (Hawkeye)Works
OpticsDifficulty: easyOpens caseNo solderingReversible15-30 min

Reverse the Hawkeye meniscus so the convex side faces the subject for a soft-edged look at close range.[9]

Special tools: small Phillips screwdriver

Good to know

  • Normal orientation has the concave side facing the subject. Flip so the convex side faces forward.[9]
  • Remove the back, two screws, and the image mask; the lens and washer come out.[9]
  • Result is a sharp zone roughly 2 to 5 feet away with soft, blurred borders; look varies per camera.[9]

⚠ Watch out

  • Written for the Brownie Hawkeye Flash only.[9]

Guides:Lens Flip! Fun with the Kodak Brownie Hawkeye! - The Film Photography Project

Pinhole conversion (Six-20)Works
OpticsDifficulty: mediumOpens caseNo solderingPermanent1-2 hr
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Strip the Six-20 lens and fit a pinhole plate; shoot 620 film with long exposures on a tripod.[6]

Special tools: needle

Good to know

  • Face plate and lens retaining ring come out with a few taps; key case parts are friction-fit with metal crimps.[6]
  • Pinhole plate is a metal disc cut to the lens retaining ring size; the hole is made with a needle.[6]
  • Pinhole-to-film distance is relatively large, so exposures are long; not handheld.[6]
  • A t-nut in built-up cardboard in a 9 mm base hole adds a tripod mount.[6]
  • Use 620 film, or respool 120 onto 620 spindles (same film size).[6]

Guides:Pinhole Miscellany » Antares (α Scorpii A)

Bluetooth screenshot shutter (Six-20 E)Experimental
Buttons & inputDifficulty: mediumOpens caseBasic solderingReversible

Friction-fit an ESP32 HID board so the Six-20 E shutter triggers a Bluetooth screenshot on a paired computer. Body left unaltered.[8]

Good to know

  • Build used a Kodak Brownie Six-20 E with an ESP32 development board in UNO form factor, friction-fit inside.[8]
  • A photo resistor sees the shutter opening; a simple roller switch is also used.[8]
  • Powered by a 9 V battery.[8]
  • Builder kept changes reversible and did not alter the body permanently.[8]

Guides:Screenshot Camera (or Grabby McScreenface) | Hackaday.io

Raspberry Pi digital conversion (Hawkeye)Works
Shell reuseDifficulty: hardOpens caseBasic solderingPermanentseveral hours
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Remove the Hawkeye lens, mount a webcam behind the shutter, wire the shutter to GPIO, and power from an external USB pack.[7]

Special tools: Dremel

Good to know

  • Build used a bakelite Kodak Brownie Hawkeye. Original lens removed; webcam sits behind the shutter in a Dremel-cut slot.[7]
  • Shutter button wired to a GPIO pin with bare wires and conductive paint.[7]
  • Stock shutter is fixed speed; a tape hack holds it open for long exposure.[7]
  • External USB power pack; drill a hole in the case for the USB cable.[7]

Guides:Building a Kodak Brownie digital camera | f/138 - Daniel Berrangé

ESP32-CAM digital conversionExperimental
Shell reuseDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace Brownie innards with an ESP32-CAM (OV2640), microSD or WiFi capture, optional M12 lens mount, and an 18650 cell.[1][2][3][11]

Parts

  • ESP32-CAM with OV2640 Fits with conditions — 2 MP OV2640; camera module can be swapped. The module has Wi-Fi and Bluetooth hardware, but the Brownie build has Wi-Fi and no Bluetooth control.[1][11][3]

Good to know

  • One build scrapped a Brownie Model 1 and fitted an ESP32-CAM where the innards were.[1]
  • OV2640 module was modified with an M12 mount for other lenses.[1][2]
  • Power from an 18650 lithium-ion cell through a boost converter; 3D-printed mounts hold the parts.[1][3]
  • No display; an indicator LED where the flash would go shows when the camera is in use.[1]
  • Firmware modes: deep sleep until a reset-button shutter wakes it to save to microSD, or networked remote control over WiFi.[1][2][3]

⚠ Watch out

  • The ESP32-CAM board has Bluetooth hardware, but this build is described as Wi-Fi only with no Bluetooth control. Do not count on Bluetooth in the finished camera.[1][3][11]

Guides:No guide found yet.

Raspberry Pi conversion (Autographic Brownie)Experimental
Shell reuseDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Fit a Raspberry Pi Zero 2W and Pi Camera V2 into a No. 2 Autographic Brownie with 3D-printed body parts, keeping the camera mechanism.[4]

Good to know

  • Build used a Kodak No. 2 Autographic Brownie with a Raspberry Pi Zero 2W and Pi Camera V2; body parts are 3D printed.[4]
  • Original lens is dark (about f/8).[4]
  • Goal was a digital conversion while preserving the camera mechanism.[4]

Guides:Digital Hacks for the Centennial Camera | Hackaday.io

Sources (11)

SOURCES.TXT