★ 83 device pages approved★ 844 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 83 device pages approved★ 844 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000086devices tracked

Home › Devices › Logitech › Logitech C270

[ device photo ]NEW!

LOGITECH · CAMERA

Logitech C270

Also called: C270 HD Webcam · Logitech C270 HD Webcam · 960-000694 · 960-001063

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 9 sources

A USB 2.0 720p webcam with a factory fixed-focus lens held by glue. Common mods open the shell, free the lens for manual focus, or strip it into an optics module for DIY microscopes and 3D scanners.[1][3][2][5][7]

3MODS
3WORK
0EXPERIMENTAL
9SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
C270HD Webcam—Logitech C270 HD Webcam. Two part numbers are in use, 960-000694 and 960-001063; check the label on your unit.[1][9]
Specs
Video720p at 30 fps[1]
ConnectionUSB 2.0[3]
FocusFixed-focus lens (no software focus control)[2]

Mods (3)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Open the front coverWorks
CaseDifficulty: easyOpens caseNo solderingReversible

Pry off the clip-on front shield, then remove three short Phillips screws to reach the lens and board.[4][6][7]

Special tools: Phillips #00 or #0 screwdriver, plastic spudger or flat blade

Good to know

  • The front cover pries off from a notch on the bottom edge; there are no screws on the outer shield.[4][6]
  • Three ~5.1 mm Phillips screws hold the inner housing (guides call for #00 or #0).[4][7]

Guides:How to Open Your Logitech C270 Webcam

Manual focus (release lens glue)Works
OpticsDifficulty: mediumOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Cut away the factory glue blob so the lens gear turns by hand. Optional: cut a slot in the faceplate so you can tweak focus with a paper clip.[2][5][6][7]

Special tools: knife or flat screwdriver, plastic spudger

Good to know

  • The C270 has a fixed-focus lens with no focus control in Logitech Webcam Software.[2]
  • Factory hot glue locks the lens; remove the glue with a knife so the gear wheel turns.[5][6][7]
  • You can score a slot in the faceplate so a paper clip reaches the lens gear without reopening the shell.[5]

Guides:Manually Focusable Logitech C270FabScan Camera

Strip into an optics moduleWorks
Shell reuseDifficulty: mediumOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Open the camera, free the lens, and mount the sensor board in a DIY microscope or 3D-scanner rig (OpenFlexure, FabScan).[7][8][9][6]

Good to know

  • OpenFlexure preparation discards the inner cover, releases the outer bezel, and frees the glued lens so the wide-angle lens can be reversed and separated from the body.[7][8]
  • Standard OpenFlexure Microscope software does not support USB cameras; use other camera software with the C270.[8][9]
  • FabScan opens the same shell and sets focus by hand for its 3D scanner camera mount.[6]

⚠ Watch out

  • OpenFlexure's preparation steps discard the inner cover, so the camera will not go back together as stock.[7]

Guides:OpenFlexure C270 preparationOpenFlexure basic optics C270FabScan Camera

Sources (9)

SOURCES.TXT