★ 177 device pages approved★ 2146 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 177 device pages approved★ 2146 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000183devices tracked

Home › Devices › Lomography › Lomo LC-A / LC-A+

Lomo LC-A / LC-A+NEW!

Photo: Pixelillo, CC BY 4.0 · AI-edited (studio background)

LOMOGRAPHY · CAMERA · 1984-2006

Lomo LC-A / LC-A+

Also called: LC-A · LC-A+ · LOMO LC-A · Lomography LC-A+

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 9 sources · 2 item(s) unverified

Compact 35 mm zone-focus cameras with automatic exposure and a vignetted Minitar lens. Common work is sticky-shutter repair, frame-counter fixes, an LC-A+ front panel on an LC-A, and a rare half-frame conversion.[1][6][7][9][4]

4MODS
3WORK
1EXPERIMENTAL
9SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
LC-AOriginal LOMO LC-A (Russia)1984Produced in St. Petersburg roughly 1984–2005. Three button cells, no cable-release thread in the shutter button. Some units carry a Zenith badge sticker under the lens. Early models can show a distance scale in the viewfinder.[1][2][5][4]
LC-A+Lomography LC-A+ (China)2006ISO 100–1600, cable-release socket, multiple-exposure switch. No distance indicator in the viewfinder. Front panel fits an ordinary LC-A (four screws) after cutting room for the second lever.[1][4][3]
Specs
Frame (stock)36×24 mm[3][9]
Lens32 mm Minitar, max aperture f/2.8 (LC-A+ manual)[3][2]
Battery3× LR44 / AG13 / 357 / SR44 (or silver-oxide S76 family)[3][1][6]
Max shutter (LC-A+)1/500[3]

Mods (4)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Sticky shutter and light-seal repairWorks
RepairDifficulty: mediumOpens caseNo solderingReversible1 hour

Open the front, clean oil and debris from the shutter and apertures, and replace crumbled foam light seals. Common failure on aging LC-A bodies.[6][8]

Special tools: Phillips screwdriver, hot air station (optional, for leatherette)

Good to know

  • Most of these cameras suffer from sticking shutter and apertures, often from oil residue or debris from aging light seals.[6]
  • Remove the three LR44 cells first. The front cover uses four Phillips 2.7 mm screws. Shutter parts should not be greased or oiled.[6]
  • The original foam light seal often turns to dust and should be replaced.[6]

⚠ Watch out

  • Two metal strips under the shutter are fragile; if they bend or break the camera will not work. Leatherette is glued and hides screws.[6]
  • Older teardown write-ups warn of a high risk of not being able to reassemble the camera.[8]

Guides:Lomo LC-A sticky shutter repair

Exposure / picture counter repairWorks
RepairDifficulty: easyOpens caseNo solderingReversible30 min

Fix a counter that will not count or will not reset after a new roll. Top-cover route; sometimes a broken reset spring replaced with a short ballpoint-pen spring.[7]

Good to know

  • Remove the three LR44 cells, then check the small levers and reset lever. Oil a sticky lever with sewing-machine oil, not WD-40.[7]
  • One documented cause was a broken reset spring fixed with a short spring from a ballpoint pen. The rewind crank comes off before the top cover.[7]

Guides:Lomo LC-A: fixing the exposure / picture counter

LC-A+ front panel on an LC-AWorks
CaseDifficulty: easyOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Swap the LC-A+ front onto an ordinary LC-A. Four screws hold the front and the sizes match, but room for the second lever must be cut with a hobby knife.[4]

Good to know

  • An ordinary LC-A can take the LC-A+ front panel: four screws hold the front, and the parts are compatible in size.[4]
  • Fitting the LC-A+ front needs room cut for the second lever with a hobby knife.[4]

Guides:No guide found yet.

Half-frame conversionExperimental
OpticsDifficulty: expertOpens caseNo solderingReversible
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Change the gate to 17×24 mm, fit a new shutter cam and film-advance wheel, add a frame-window insert, and mask the viewfinder. Roughly doubles frames per roll. Advanced metal and 3D-print work.[9]

Good to know

  • One 2024 build report covers a half-frame mod for both the LC-A and LC-A+, based on a 1999 Russian magazine clipping.[9]
  • Frame becomes 17×24 mm instead of 36×24 mm. A new shutter cam cocks the shutter in half the movements. Metal parts were laser-cut and hand-finished.[9]
  • Only the front and bottom panels must come off for the mechanical parts; the frame-window insert needs no further disassembly. Viewfinder masking uses two 5×11 mm tape strips.[9]
  • Keep the removed original parts to return to full-frame. Result is about 72 frames from a 36-exposure roll; landscape shots need the camera turned.[9]

⚠ Watch out

  • Rated as an advanced project needing fabricated metal parts and 3D printing.[9]

Guides:How I modded Lomo LC-A+ into half-frame camera - 35mmc

Sources (9)

SOURCES.TXT