★ 109 device pages approved★ 1201 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 109 device pages approved★ 1201 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000115devices tracked

Home › Devices › Motorola › Motorola Advisor pager

[ device photo ]NEW!

MOTOROLA · OTHER · 1990

Motorola Advisor pager

Also called: Advisor · Advisor II · Motorola Advisor POCSAG · Motorola Advisor FLEX

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 8 sources · 2 item(s) unverified

1990s Motorola Advisor alphanumeric pagers (and Advisor II). Documented projects replace the radio path with BLE phone notifications over POCSAG, or swap in LoRa boards; crystal changes and serial reprogramming are also documented.[8][1][4][2][7]

4MODS
2WORK
2EXPERIMENTAL
8SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
AdvisorOriginal alphanumeric (1990)1990Compact alphanumeric pager from 1990. Many re-brands exist. Teardown units run on one AAA, but one source lists a single AA; check the holder on your unit.[8][1][3][5]
Advisor IIFLEX or POCSAG (discontinued)—Later Advisor II: VHF/900 MHz FLEX or VHF/UHF/900 MHz POCSAG. Official page lists 1.5 V AA alkaline. Same BLE/POCSAG build has been reported working on Advisor II.[7][1]
Specs
DisplayOriginal Advisor: up to four lines, up to 20 characters per line. Advisor II: up to four lines, up to 80 characters per line.[8][7]
Size (Advisor)18.5 × 55 × 81 mm[8]
BatterySingle alkaline cell; teardown and build reports say AAA for the original Advisor, IEEE Spectrum and Advisor II official say AA — check your unit[3][5][8][7]
ProtocolsPOCSAG (common on Advisor builds); Advisor II also sold as FLEX[3][7]

Mods (4)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Phone notifications over BLE and POCSAGWorks
ConnectivityDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Keep the Advisor case and display: an ESP32 (or similar) receives Android notifications over Bluetooth LE and drives the pager’s POCSAG path so messages show on the screen.[1]

Special tools: Arduino-compatible programmer

Parts

  • ESP32-C6 (or similar) BLE board Fits with conditions — Hackster build tested Arduino Pro Mini plus ESP32-C6 for BLE to POCSAG.[1]
  • 3.7 V 10440 Li-ion cell with step-down converter Fits with conditions — Replaces the 1.5 V AAA; the cell is slightly longer than the stock holder, so the holder must be modified or replaced with a 3D-printed one. Runtime is only a few hours with both boards and BLE on.[1]

Good to know

  • The build is a 1990s Advisor that shows Android phone message notifications on the pager display.[1]
  • Program the pager to 512 bps and note the capcode before removing the radio.[1]
  • No screws hold the case; a sliding panel and battery latch open it.[1]
  • The same approach also worked on an Advisor II and a Unication E3 for the author.[1]
  • The phone app used in the guide is Android only; there is no iOS version at the time of writing.[1]

⚠ Watch out

  • Some pins carry voltage that can turn the pager off or harm chips if grounded; keep them insulated.[1]
  • A 3.7 V Li-ion cell needs a step-down converter for the 1.5 V pager electronics.[1]
  • Programming software is an old DOS-era tool that does not run on modern Windows.[1]

Guides:Motorola Pager given new life with Bluetooth BLE - Hackster.io

LoRa radio board swapExperimental
ConnectivityDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Pull the stock RF board and fit an Arduino Pro Mini plus an RFM95W LoRa module. Only build notes exist.[4]

Parts

  • Arduino Pro Mini (3.3 V) Fits with conditions — Used with an RFM95W and a voltage booster in the MotoLoRa notes.[4]
  • RFM95W LoRa module Fits with conditions — Replaces the original radio board path.[4]

Good to know

  • The project replaces the radio board of an old Advisor with Arduino and LoRa boards.[4]
  • A fresh AAA lasted about 22 hours in that build; the author suspects the LoRa module is the biggest power draw.[4]
  • The radio board can be pulled out and swapped; one unit was found parked on a marine VHF frequency.[4]

⚠ Watch out

  • Transmitting on radio bands may require a licence where you live.[4]

Guides:No guide found yet.

Custom crystal for a new receive frequencyExperimental
OtherDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

The Advisor’s receive frequency is set by a crystal. Changing bands means ordering a custom-cut crystal; crystal-locked units are a lot of work.[2][3]

Good to know

  • The pager’s frequency is set by a crystal; a custom crystal must be cut for a new frequency.[2]
  • Example: a UHF Advisor set to the DAPNET frequency 439.9875 MHz with a 49.37634375 MHz third-overtone crystal.[2]
  • The RF board is a removable crystal-locked module; these pagers are a lot of work to re-crystal.[3]

⚠ Watch out

  • Operating on a new frequency may need a licence or authorised service where you live.[2]

Guides:No guide found yet.

Serial reprogramming (capcode and settings)Works
SoftwareDifficulty: mediumCase stays closedNo solderingReversible
  • ⚠ Data loss Can erase what is on the device. Back up first.

Set capcode and operating options over 3.3 V TTL serial with Motorola-era programming software. Needed before many radio mods.[2][6][3][1]

Special tools: 3.3 V TTL serial adapter

Good to know

  • Programming uses 3.3 V TTL serial at 9600 baud, 8N1.[2]
  • Programming software sets the CAP code and other operating settings.[2]
  • A homemade three-wire interface (TXD, RXD, ground) has been used on the Advisor; a circuit built for other pager types can seriously damage a pager.[6]
  • Programming needs Motorola-specific software that is no longer supported.[3]

⚠ Watch out

  • Use a programming circuit made for your pager type; a circuit built for other pagers can seriously damage it.[6]

Guides:No guide found yet.

Sources (8)

SOURCES.TXT