★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000206devices tracked

Home › Devices › Nikon › Nikon D200

[ device photo ]CUSTOM FW!

NIKON · CAMERA · 2005

Nikon D200

Also called: D200 · Nikon D200 DX

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 11 sources

10.2 MP DX DSLR with CompactFlash and an EN-EL3e pack. Common work is the official A/B firmware update and a hot-mirror swap for infrared; DIY IR needs soldering and high-voltage care.[1][2][6][7]

3MODS
3WORK
0EXPERIMENTAL
11SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearFirmwareHow to tell
D200DX body20052.01Magnesium weather-sealed body, CompactFlash slot, EN-EL3e battery. Announced November 2005.[4][1][2]
Specs
Sensor10.2 MP DX CCD (about 23.6 × 15.8 mm)[4][5]
Screen2.5-inch TFT LCD, about 230,000 pixels[4][1]
StorageCompactFlash Type I/II; Hitachi Microdrive also listed[1][4][5]
BatteryEN-EL3e Li-ion (not the D100 EN-EL3); about 1,800 shots rated[1][4][5]
Flash sync1/250 sec; Auto FP high-speed sync above 1/250[1][5]

Mods (3)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Official firmware 2.01 (A and B)Works
SoftwareDifficulty: easyCase stays closedNo solderingPermanent15-30 min
  • ⚠ Can brick A mistake can leave the device unable to start.

Update both A and B firmware sets from Nikon’s download. Fixes a rare blinking battery indicator. Copy one .bin at a time to the card root.[3][2]

Good to know

  • Firmware 2.01 upgrades both A and B sets. Correct operation is not guaranteed if only one set is updated.[2][3]
  • Copy only one of the A or B files to the card at a time, in the root directory, not in a folder.[2][3]
  • Do not use Microdrive cards for the update. Use an EH-6 AC adapter or a fully charged EN-EL3e.[3]
  • 2.01 resolves a rare fault where the battery indicator blinks while shooting.[2]

⚠ Watch out

  • Power loss or pressing camera controls during the update may damage the camera.[3]

Guides:Upgrading the Firmware for the D200Nikon | Download center | D200 Firmware

Custom white balance after IR conversionWorks
SoftwareDifficulty: easyCase stays closedNo solderingReversible5 min

On an IR-converted D200, set a PRE white balance from green grass so JPEGs are not reddish. RAW keeps the sensor data.[8]

Good to know

  • Standard white-balance settings on an IR-converted D200 produce reddish images.[8]
  • Use PRE with the WB button and photograph healthy green grass in similar light; the camera should show “Good”.[8]
  • White balance applies to JPEGs; RAW files keep the sensor data.[8]

Guides:Custom White Balance for Nikon D200 IR | Geospatial Modeling & Visualization

Infrared hot-mirror conversionWorks
OpticsDifficulty: hardOpens caseBasic solderingPermanent2-4 hr
  • ⚠ Stored charge Capacitors keep a dangerous charge after the device is off.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace the OEM hot mirror with an IR-pass filter (often ~720 nm). DIY needs desoldering and high-voltage care; vendors also offer the service with AF calibration.[6][7][9][10][11]

Special tools: small Phillips screwdriver, tweezers, canned air, lens cleaning kit, grounding strap with current-limit resistor

Parts

  • Standard color IR filter (~720 nm / Hoya R72 / Wratten 89B) Fits — Common choice for IR-only builds; a university D200 build uses this class of filter, and Life Pixel sells it as its standard color IR filter.[11][7][6] Buy: lifepixel.com
  • Life Pixel D200 IR DIY path Fits — 17-step hot-mirror swap tutorial from a conversion seller.[6] Buy: lifepixel.com
  • MaxMax D200 IR conversion service Fits — Historical vendor page: IR+Visible, IR-only (715–1200 nm), or Visible Hot Rod. Manual exposure compensation needed; warranty void.[9] Buy: maxmax.com
  • Kolari Vision D200 IR conversion Fits — D200 listed among convertible Nikon bodies; AF calibration to 50 mm or a custom lens included.[10] Buy: kolarivision.com

Good to know

  • DIY: remove battery door, pads, screws and cables, lift the sensor unit, remove the filter spring, frame and hot mirror, then fit the IR filter.[6]
  • One DIY step desolders a ground tab on the sensor assembly.[6]
  • A university lab replaced the hot mirror with a filter that blocks wavelengths below 720 nm (Hoya R72 / Wratten 89B class) and calibrated AF for one 28 mm AF Nikkor.[7]
  • IR-only cameras typically see about 715 nm to 1200 nm. The D200 meters through a separate light sensor, so set exposure compensation by hand.[9]
  • Focus and dust are the hardest parts of the conversion; Life Pixel does not publish focus-calibration steps.[6]

⚠ Watch out

  • High voltage inside the camera can injure or kill. Guide is for experienced users only.[6]
  • Modification voids the warranty.[9][6]

Guides:Life Pixel – Nikon D200 DIY Digital Infrared Conversion TutorialNikon D200 IR | Geospatial Modeling & Visualization

Sources (11)

SOURCES.TXT