★ 155 device pages approved★ 1835 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 155 device pages approved★ 1835 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000161devices tracked

Home › Devices › Nintendo › Nintendo Game & Watch (classic monochrome, Sharp SM5A/SM510/SM511/SM512)

[ device photo ]NEW!

NINTENDO · HANDHELD CONSOLE · 1980-1991

Nintendo Game & Watch (classic monochrome, Sharp SM5A/SM510/SM511/SM512)

Also called: Game & Watch · G&W classic · SM5A · SM510 · SM511 · SM512

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 7 sources · 2 item(s) unverified

Classic 1980–1991 monochrome Game & Watch handhelds on Sharp SM5A / SM510 / SM511 / SM512 chips (not the later Mini or 2020 colour units). Hardware mods are rare: one tabletop TFT rebuild, cosmetic refurbs, and DIY button rubbers. Battery type varies by series.[1][2][3][4]

4MODS
2WORK
2EXPERIMENTAL
7SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
SM5A / SM510 / SM511 / SM512 familyClassic monochrome Game & Watch (1980–1991)1980-1991Original LCD Game & Watch lines through 1991. Not the SM530 Game & Watch Mini, and not the 2020+ colour USB-C remakes.[1][7]
Specs
MCU familySharp SM5xx: SM5A (~1,792 B ROM), SM510 (~2,772), SM511/SM512 (~4,032); 32.768 kHz crystal[1]
Battery (varies by series)Often 2× LR43/SR43 or LR44 on handhelds; some tabletops use other sizes (e.g. 2× LR14 C-cell on CJ-71). Check the compartment marking.[6][4][2][3]

Mods (4)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

TFT LCD rebuild (tabletop, RP2040)Experimental
ScreenDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

One build log replaces a dead Donkey Kong Jr. tabletop (CJ-71) LCD with a 480×320 ILI9488 TFT driven by a Raspberry Pi Pico, keeping the original SM511, piezo and controls.[2]

Good to know

  • CJ-71 Donkey Kong Jr. tabletop: Sharp SM511 MCU; joystick, buttons and piezo still worked after the LCD failed.[2]
  • Screen replaced with a 480×320 ILI9488 TFT driven by an RP2040 (Raspberry Pi Pico).[2]
  • Original 2× LR14 C-cells feed an XL6019 boost converter to 5 V for the Pico. The piezo is driven from a GPIO pin; the shell acts as a resonator.[2]

⚠ Watch out

  • Single build log for one tabletop model. Do not assume the same steps fit other Game & Watch form factors.[2]

Guides:DONKEY KONG JR. TABLE TOP REVIVAL (CJ-71) | Hackaday.io

Cosmetic refurb and screen reassemblyWorks
RepairDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Open a classic unit, clean pads, repaint/labels, and reassemble the LCD stack in the correct order. One Donkey Kong write-up documents screw counts and speaker desoldering.[3]

Special tools: soldering iron

Good to know

  • Donkey Kong refurb: opening takes 9 + 9 screws; two speaker cables must be desoldered and later resoldered.[3]
  • Screen layer order matters — wrong order leaves the display dark.[3]
  • Author cleaned buttons and rubber pads rather than replacing them; paint and labels were cosmetic.[3]

⚠ Watch out

  • Thin plastic screen parts can deform in hot water.[3]

Guides:Game & Watch Donkey Kong refurbish - Dreamcast.nu

Tabletop button rubber padsExperimental
Buttons & inputDifficulty: easyCase stays closedNo solderingReversible

Missing tabletop rubber pads are hard to buy as spares. Collectors use common rubber feet or donor units.[5]

Good to know

  • In a 2014 forum thread, an owner of four tabletops reports several missing rubber button pads and no spares to buy.[5]
  • Advice on that thread: use common rubber feet from a local shop, or buy a broken unit for parts.[5]

Guides:No guide found yet.

Correct battery typeWorks
BatteryDifficulty: noneCase stays closedNo solderingReversible

Battery chemistry and size depend on series and year. Wrong cells can bend terminals.[4][6]

Good to know

  • gameandwatch.ch FAQ tables battery types by series and year (e.g. BW blue-on-white 1980–1982: LR-43).[4]
  • iFixit lists two LR43 or SR43 alkali-manganese cells for the original Game & Watch specs, and notes later variants may differ.[6]
  • LR-43 cells may fit many LR-44 games but contact and life can be poor. Putting LR-44 cells in LR-43 games can bend the terminals and damage the unit.[4]

Guides:No guide found yet.

Sources (7)

SOURCES.TXT