★ 208 device pages approved★ 2530 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 208 device pages approved★ 2530 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000214devices tracked

Home › Devices › Nintendo › Nintendo Pokéwalker

[ device photo ]NEW!

NINTENDO · HANDHELD CONSOLE · 2009-2010

Nintendo Pokéwalker

Also called: Pokewalker · Pokéwalker · HeartGold SoulSilver pedometer

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 16 sources · 3 item(s) unverified

Pedometer accessory for Pokémon HeartGold and SoulSilver. Common fixes are the CR2032 battery and plastic buttons. Researchers have run code over IR, but no custom firmware or custom-course tools shipped.[6][9][10][1]

6MODS
2WORK
3EXPERIMENTAL
16SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
PokéwalkerHeartGold / SoulSilver bundle2009One hardware revision bundled with HG/SS. Japan September 2009; Western releases in 2010. IR pairing needs a genuine cartridge with the IR transceiver.[6][1]
Specs
Screen96×64 4-shade grayscale LCD (Solomon SSD1854)[6]
Storage64 KiB EEPROM save (ST M95512)[6]
CPU / sensorsRenesas H8/38606R, 2 KiB RAM; Bosch BMA150 accelerometer; IR IrDA-SIR 115200 8N1[6][2]
BatteryCR2032 3 V coin cell, about 220–225 mAh; not rechargeable[6]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

CR2032 battery replacementWorks
BatteryDifficulty: easyOpens caseNo solderingReversible10-15 min
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Open the back with a Phillips #0 screw and swap the coin cell. Removing the cell mid-session deletes unsaved steps, watts, items and Pokémon on the walker.[9][6][7]

Special tools: Phillips #0 screwdriver, spudger

Parts

  • CR2032 lithium coin cell Fits — 3 V non-rechargeable. One commenter suggests positive side up.[9][6]

Good to know

  • Remove the single back screw with a Phillips #0, then lift the cell with a spudger.[9]
  • The battery is not rechargeable; replace with another CR2032 when it runs out. Life is about four months at roughly 30 minutes and 10,000 steps a day.[6]
  • Muting sound in Settings helps preserve battery life.[7]

⚠ Watch out

  • Removing the battery during a session deletes unsaved steps, watts, items and Pokémon on the walker.[6]

Guides:Pokewalker Battery Replacement - iFixit

Button replacementWorks
RepairDifficulty: mediumOpens caseNo solderingReversible20-40 min

Replace cracked plastic buttons. Needs a Y0 tri-wing for the inner cover; keep the screen ribbon connected while the halves are open.[10][11][12]

Special tools: Phillips #0 screwdriver, Y0 tri-wing screwdriver

Good to know

  • Remove the battery and back screw, then four Y0 tri-wing screws on the case.[10]
  • Do not fully separate the halves; the display stays on a ribbon cable. Do not force the cable when reseating.[10]
  • Three plastic buttons come out one at a time and only fit one way.[10]
  • Full disassembly also uses PH000 and a spudger; the speaker is attached to the internal casing and would need soldering to separate from the motherboard. Plastic can be frail on reassembly.[11]

Guides:Pokewalker Button Replacement - iFixitPokewalker Disassembly - iFixit

IR research / code executionExperimental
SoftwareDifficulty: expertCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Researchers can run code on the walker over IR and dump flash in chunks before the watchdog resets. No released custom firmware; programming the CPU erases onboard flash.[1][2][4]

Good to know

  • The walker talks to the game over infrared; the IR transceiver is in the game cartridge because the DS has none.[1]
  • A remote IR exploit can run arbitrary code. Dumping works in chunks of about 22K before the watchdog resets the device.[1][2]
  • The CPU is programmable, but any attempt to program it erases the onboard flash.[2]

Guides:PokéWalker hacking - Dmitry.GR

Event courses via save editExperimental
SoftwareDifficulty: mediumCase stays closedNo solderingReversible
  • ⚠ Data loss Can erase what is on the device. Back up first.

Official Wi-Fi course servers are gone. Forums say some event courses may be unlocked with save edits or AR codes.[16][8][5][3][15]

Good to know

  • Official servers can no longer be reached for downloadable courses.[16][8]
  • Unlocking courses through AR codes or save edits may be possible (forum reports).[16]
  • A Pokémon on the walker is linked to the cartridge; the full data lives in the save. Without the matching cart, rescue from the walker alone is not possible.[3][15]

Guides:No guide found yet.

Custom coursesNot possible
SoftwareDifficulty: expertCase stays closedNo solderingReversible

A 2022 moderator reply says no tools to build custom Pokéwalker courses exist.[13]

Good to know

  • A Project Pokémon moderator replied that they do not believe any custom-course tools exist.[13]
Sprite RAM hack at syncExperimental
SoftwareDifficulty: hardCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.

2012 research changed walker sprites by AR-copying data into HG/SS RAM at the transfer screen. Experimental; one bad pointer froze the game.[14]

Good to know

  • Pokéwalker graphics are stored on HG/SS and loaded into RAM at sync.[14]
  • Sprites were changed with an AR code that copies data from a modified GBA save into RAM.[14]
  • A test with a changed pointer froze the game about a second later.[14]

Guides:No guide found yet.

Sources (16)

SOURCES.TXT