★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000054devices tracked

Home › Devices › Nintendo › Nintendo Switch

[ device photo ]NEW!

NINTENDO · HANDHELD CONSOLE · 2017

Nintendo Switch

Also called: Switch · HAC-001 · HAC-001(-01) · Mariko

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 9 sources · 2 item(s) unverified

Nintendo's hybrid console (March 2017). Unpatched V1 units can run Atmosphere by injecting a USB payload in Recovery Mode. Patched hardware needs a modchip. Joy-Con sticks and the internal battery are documented repairs.[1][2][3][6][9][8]

4MODS
4WORK
0EXPERIMENTAL
9SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
HAC-001Unpatched V12017Early units open to the Fusee Gelee bootROM bug. An RCM jig and USB payload can launch custom firmware without a modchip.[2][3][6]
HAC-001Patched V12018Later V1 hardware with the bootROM bug closed. Softmod via RCM does not work; these need a hardware modchip.[3][6]
HAC-001(-01)2019 revision—Revised 2019 model with an improved Tegra X1 chip, sold as HAC-001(-01).[1][8]
Specs
SoCCustom Nvidia Tegra X1[1]
Screen6.2-inch capacitive LCD, 1280×720[1]
Battery16 Wh lithium-ion[7]

Mods (4)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Atmosphere on an unpatched V1Works
SoftwareDifficulty: mediumCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

On an unpatched V1, an RCM jig in the right Joy-Con rail enters Recovery Mode and a USB payload starts Hekate or Atmosphere before Horizon boots. Atmosphere supports an emulated NAND (emuMMC) on the SD card.[2][3][4][5][6]

Parts

  • RCM jig Fits with conditions — Sits in the right Joy-Con rail to enter Recovery Mode. Unpatched V1 only.[2]

Good to know

  • Unpatched V1 units use a Tegra X1 bootROM bug (Fusee Gelee). An RCM jig in the right Joy-Con rail enters Recovery Mode, then a USB payload is injected before Horizon starts.[2][3][6]
  • Atmosphere is modular custom firmware that patches Horizon on the fly. It provides customized system modules, cheats, themes, sysmodules, and title redirection for homebrew.[4][3]
  • Atmosphere supports an emulated NAND (emuMMC) on the microSD card. Guides describe partitioning the card for emuMMC to keep stock SysNAND separate.[2][4]
  • Hekate is a GUI bootloader for launching payloads, raw eMMC backup/restore, hardware diagnostics, SD partitioning, and AutoRCM.[5]
  • Patched units close the bootROM bug and need hardware installed beforehand (a modchip) instead of this softmod.[3][6]

⚠ Watch out

  • This Recovery Mode method is for unpatched V1 units only.[3][2]
  • Online misbehavior on a modded console can get it banned. The install guide says bans target misbehavior, not the presence of custom firmware alone, and recommends emuMMC.[2][3] unverified

Guides:The Ultimate Noob Guide for Hacking your Nintendo SwitchNH Switch Guide

Modchip for patched consolesWorks
OtherDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Patched consoles cannot use the RCM softmod. The install guide says they need specialized hardware installed first, such as a modchip, before custom firmware can run.[3][6]

Parts

  • Switch modchip (patched units) Fits with conditions — Needed on units where the Tegra bootROM exploit is patched.[3]

Good to know

  • New Switch consoles appeared in 2018 with the Nvidia Tegra hardware exploit patched; older units still work.[6]
  • The guide says it works on V1 unpatched and modchipped consoles; other (patched) consoles need specialized hardware installed beforehand.[3]

⚠ Watch out

  • Modchip installs are precision soldering with a real brick risk.[3][6] unverified

Guides:No guide found yet.

Joy-Con joystick replacementWorks
RepairDifficulty: mediumOpens caseNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Replace a drifting Joy-Con stick module. iFixit documents opening the Joy-Con, disconnecting the battery and ribbons, and swapping the potentiometer module. iFixit also offers an aftermarket GuliKit TMR stick as an alternative.[9]

Special tools: Tri-point Y00 and Phillips #00 screwdrivers, spudger, tweezers

Good to know

  • iFixit's left Joy-Con guide replaces the joystick module after disconnecting the internal battery, middle frame, and ribbon cables.[9]
  • The guide lists a GuliKit TMR joystick as an alternative to the standard joystick.[9]

Guides:Left Joy-Con Joystick Replacement - iFixit

Replace the Switch batteryWorks
BatteryDifficulty: mediumOpens caseNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Swap the internal lithium pack. Discharge below 25% first. Needs a Tri-point Y00 for the rear case and isopropyl alcohol for the adhesive under the cell.[8][7]

Special tools: Tri-point Y00, JIS 00, isopropyl alcohol

Good to know

  • The Switch has a 16 Wh battery held in with adhesive.[7][8]
  • Discharge the battery below 25% before opening. Soften adhesive with isopropyl alcohol; do not puncture the cell.[8]

Guides:Nintendo Switch Battery Replacement - iFixit

Buttons & modes

BUTTONS.TXT
WhatHow
Recovery Mode payload (unpatched V1)Fit an RCM jig in the right Joy-Con rail, then send a Fusee Gelee payload over USB before the OS boots.[2]

Sources (9)

SOURCES.TXT