★ 93 device pages approved★ 980 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 93 device pages approved★ 980 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000096devices tracked

Home › Devices › Nokia › Nokia 3210

[ device photo ]NEW!

NOKIA · PHONE · 1999

Nokia 3210

Also called: NSE-8 · Chameleon · DCT3

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 11 sources · 4 item(s) unverified

1999 GSM candybar (NSE-8 / DCT3) with an 84×48 monochrome screen, clip-on Xpress-on covers, and a removable NiMH pack. Documented mods swap cover fascias, add backlight LEDs and vibra, or drop in unfinished replacement boards (2017 Hackaday retrofit; 2026 4G prototype).[9][10][2][4][6]

4MODS
2WORK
2EXPERIMENTAL
11SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearFirmwareHow to tell
NSE-8Nokia 3210 (1999)1999NSE-8Announced at CeBIT 18 March 1999. Codename Chameleon. Removable BML-3 NiMH pack, clip-on front and rear covers. Not the 2024 HMD Nokia 3210 relaunch.[9][10][11]
Specs
Screen1.5-inch backlit monochrome LCD, 84×48[9]
BatteryRemovable Nokia BML-3 NiMH, 2.4 V (Wikipedia lists 1250 mAh)[9][11]
ChargerNokia ACP-7E, 3.7 V / 355 mA output[11]
NetworkGSM 900/1800 (2G only on the stock phone)[9][4]

Mods (4)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Xpress-on / clip-on coversWorks
CaseDifficulty: easyCase stays closedNo solderingReversible

Front and rear covers clip off so you can change how the phone looks; third parties made custom fascias.[10][9]

Good to know

  • Both the front and rear covers could be changed; third parties made custom covers.[10]
  • The design has customizable fascias that clip on.[9]

Guides:No guide found yet.

Backlight LED colour and vibra motorWorks
Buttons & inputDifficulty: hardOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace the green display/keypad LEDs for a different colour and fit an eccentric-weight vibra motor. Needs fine soldering and a Torx T6.[8][7][9]

Special tools: Torx T6, fine-tip soldering iron, multimeter

Good to know

  • A 2002 Hardware Upgrade guide covers swapping the green LEDs that light the display and keypad, and installing an eccentric-weight vibra motor.[8]
  • Stock teardown uses Torx T6 screws after the battery cover, battery, and SIM come off.[7]
  • Vibrate was in the original design but dropped on some handsets; repair shops later offered a vibrate upgrade.[9] unverified

Guides:Personalizzazione Nokia 3210 | Pagina 1: Introduzione | Hardware Upgrade

2017 replacement retrofit boardExperimental
OtherDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Hackaday Prize concept: a drop-in board with the same footprint and button layout, STM32F7, A7 GSM/GPRS, ESP8266 WiFi, and a planned 160×128 OLED. Boards were ordered; no finished unit or firmware is shown.[2][1]

Good to know

  • The board is meant to fit where the original circuit board sits, with the same button and LED layout, inside the original enclosure.[2][1]
  • Planned parts include an STM32F756 (or STM32 F7), ESP8266 WiFi (no Bluetooth), A7 GSM module, and a 160×128 SEPS525 OLED replacing the stock screen.[2][1]
  • As of the 2017-11-19 build log, ten six-layer boards were ordered from EasyEDA; the project page shows no finished unit or firmware.[2]

Guides:Nokia 3210 Retro Fit Board | Hackaday.io

2026 4G replacement board (prototype)Experimental
OtherDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

A reverse-engineered DCT3 motherboard for the original case that aims at 4G and a lithium-ion cell while keeping the monochrome screen and buttons. Still a prototype; firmware unfinished; hardware release undecided.[4][6][5][3]

Good to know

  • The modder reverse-engineered the DCT3 platform (also used in Nokia 5110, 7100, 8810) to build the board.[4][5]
  • The plan keeps the original case, buttons, and monochrome screen, and targets a 4G module plus a standard lithium-ion battery in place of the NiMH pack.[6][3]
  • As of mid-2026 reporting, the project is not finished: firmware still needs work, and the modder plans to release firmware first while hardware release is undecided.[6][4][5]
  • The stock phone only supports 2G; carriers are shutting that network down.[4]

Guides:No guide found yet.

Sources (11)

SOURCES.TXT