★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000054devices tracked

Home › Devices › Nokia › Nokia 3310

[ device photo ]NEW!

NOKIA · PHONE · 2000

Nokia 3310

Also called: NHM-5 · DCT3

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 9 sources · 1 item(s) unverified

Nokia's 2000 candybar phone. It has an 84×48 monochrome screen, a barrel charging jack, and swappable Xpress-on covers. Documented changes add USB-C, a bigger lithium cell, reuse the screen on a microcontroller, or put a new board in the shell.[1][2][6][5][8]

5MODS
3WORK
2EXPERIMENTAL
9SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
NHM-5Nokia 33102000Released in Q4 2000. 84×48 monochrome screen with a backlight. Removable BMC-3 NiMH or BLC-2 Li-ion pack. Barrel jack for charging. Front and back Xpress-on covers come off.[1][7] unverified
Specs
Screen84×48 monochrome, backlit, PCD8544 controller[7][5][4]
BatteryRemovable BMC-3 NiMH 900 mAh or BLC-2 Li-ion 1000 mAh[1]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Xpress-on coversWorks
CaseDifficulty: easyCase stays closedNo solderingReversible

The front and back covers come off so you can change how the phone looks.[7][1]

Parts

  • Xpress-on front and back covers Fits — Interchangeable covers for the NHM-5.[7][1]

Good to know

  • The 3310 can be customized with interchangeable Xpress-on covers.[7]
  • Front and back Xpress-on faceplates come off for a different look.[1]

Guides:No guide found yet.

USB-C charging boardWorks
ChargingDifficulty: mediumOpens caseNo solderingReversible

A drop-in board replaces the barrel jack with USB-C. Spring pins make it solderless. You move the microphone onto the new board.[2][3]

Parts

  • Andrea Salvatori USB-C charging board Fits — Pogo pins match the original charging-port footprint. The microphone capsule moves over from the old board. Charges from 5 V USB without Power Delivery.[2]

Good to know

  • Andrea Salvatori's board is a drop-in USB-C replacement. Spring pogo pins match the original charging port, so the install is solderless.[2]
  • The microphone capsule has to be moved from the original board onto the new one.[2]
  • It charges from 5 V USB power and does not need Power Delivery negotiation.[2]
  • The part can be removed and replaced with relative ease, and no soldering is required.[3]

Guides:No guide found yet.

Larger lithium packExperimental
BatteryDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

A DIY build wires a larger Li-pol cell in place of the original pack. The phone needs the correct ID and thermistor resistor values on the battery pads, or it will not turn on.[6]

Good to know

  • The original battery has four terminals: power, ground, a thermistor, and a fixed resistor for cell-type ID. The phone will not turn on unless both sense pads are connected correctly.[6]
  • Li-ion / Li-pol charging is selected with about 74.5 kΩ from the ID pad to ground. A fixed ~45 kΩ resistor can stand in for the thermistor at room temperature.[6]
  • One build used a 2500 mAh protected Li-pol cell wired to the board after removing the battery-connector module, and reported about 350 hours on standby.[6]
  • That thicker cell left a small gap between the case halves after reassembly.[6]

⚠ Watch out

  • Wrong ID or thermistor values keep the phone from powering on. Match the resistor setup before sealing the case.[6]

Guides:Nokia 3310 USB-C and battery modification

PCD8544 screen on a microcontrollerWorks
ScreenDifficulty: mediumOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

The 84×48 screen is a Philips PCD8544. People remove it and drive it from a microcontroller.[5][1][9]

Good to know

  • The screen is an 84×48 monochrome LCD with a Philips PCD8544 controller.[5][1]
  • Hackaday points to an Instructables write-up that drives a salvaged 3310 LCD from an ATmega8, with pinouts and source code.[9]

Guides:Overview | Nokia 5110/3310 Monochrome LCDConnecting A Nokia 3310 LCD Using An AVR

Custom board in the 3310 shellExperimental
Shell reuseDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Projects gut the phone and fit a custom board that keeps the original display. One recent build uses a Raspberry Pi Pico.[4][8]

Good to know

  • The 1337 3310 Tool project replaces the Nokia motherboard with a custom microcontroller board inside the original shell.[4]
  • That build keeps the original function buttons and the display. The numeric pad was dropped to route the traces.[4]
  • A 2026 game-jam restomod guts a real 3310 and fits a custom PCB with a Pi Pico, the Nokia LCD, and a Nokia keypad layout.[8]

Guides:No guide found yet.

Sources (9)

SOURCES.TXT