Home › Devices › Olympus › Olympus OM-2n
NEW!Photo: John Nuttall from Hampshire, United Kingdom, CC BY 2.0 · AI-edited (studio background)
OLYMPUS · CAMERA · 1979-1984
Olympus OM-2n
Also called: OM-2N · OM-2N MD · Olympus OM-2N
1979–1984 Olympus OM-2n 35 mm SLR. Almost entirely mechanical: common work is freeing a jammed winder/shutter, replacing light seals and mirror damper pads, fixing the power switch, and removing prism foam before it eats the silvering.[1][2][3][6][4]
Which one do I have?
Specs
Mods (5)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Free a jammed winder or shutterWorks
One documented jam was a loose screw on the rewind shaft under the bottom plate blocking the gear train. Use JIS drivers; opening the top plate can cause more harm than good.[2][1]
Special tools: JIS screwdriver set, pin wrench
Good to know
- One documented jam was a loose screw on the bottom end of the rewind shaft that stopped a gear; tightening it freed the winder and shutter.[2]
- The body is almost entirely mechanical, so this fault was not electronic.[2]
- The bottom plate uses four cross-head screws; use JIS drivers because Phillips can strip the heads.[2][1]
- Many parts are shared between OM-1, OM-2, OM-3, and OM-4, so guides for one can often apply to another.[2]
⚠ Watch out
- Opening the top plate caused more harm than good on the documented body (foam, on/off dial, film counter). Think before opening sections that may not be the fault.[2]
Guides:Fixing an Old Film Camera, Part 2: First, Do No HarmFinding and Fixing an Old Film Camera, Part 1
Replace light seals and mirror damper padsWorks
Replace door light seals and mirror damper foam before the first film. Match original thickness (about 1 mm on the documented body) and protect the shutter while cleaning.[3]
Special tools: isopropyl alcohol, card scrap to protect shutter
Good to know
- Replace the light seals, the mirror damper pads, and do basic cleaning before the first film.[3]
- Keep seal material the same thickness as the original; look up the model for the right thickness (about 1 mm was used on that body).[3]
- Clean the channel with isopropyl alcohol and tape card over the shutter to protect it.[3]
⚠ Watch out
Guides:Fixing an Old Film Camera, Part 3: Fixing the Light Seals and Shooting
Remove prism foamWorks
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
All OM-2N bodies have prism foam that can release acid and dissolve prism silvering. Closest step guide is written for the OM-1; confirm fit before you dig in.[6]
Good to know
- All OM-2N versions have prism foam installed.[6]
- As the foam degrades it releases an acidic goo that slowly dissolves the prism silvering — a terminal fault.[6]
- Remove batteries and set the meter switch to OFF before work.[6]
⚠ Watch out
Repair the power / mode switchExperimental
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
The switch selects manual, auto, off, and battery check. Misalignment when refitting the top plate can break the internal fork; one repair used plywood tips and superglue.[2][5]
Good to know
Fit meter batteriesWorks
A battery finder lists 2× LR44 for the OM-2n. Check the cell type on your body before buying.[7][5]
Parts
- 2× LR44 Fits with conditions — Listed by a seller's battery finder; cell type not confirmed by a second source.[7] Buy: ausgeknipst.de
Good to know
- An Olympus battery finder lists the OM-2n as 2× LR44.[7]
- The power switch includes a battery-check position.[5]
Guides:No guide found yet.
Sources (7)
- docs Finding and Fixing an Old Film Camera, Part 1 · 2026-11-16
- docs Fixing an Old Film Camera, Part 2: First, Do No Harm · 2026-11-16
- docs Fixing an Old Film Camera, Part 3: Fixing the Light Seals and Shooting · 2026-11-16
- wiki Olympus OM-2 - Wikipedia · 2026-11-16
- blog Olympus OM-2n - By Bob Janes - 35mmc · 2026-11-16
- blog Olympus OM-1 Prism Foam Removal · 2026-11-16
- shop Olympus Battery Finder — Type for Every Model · 2026-11-16