★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000147devices tracked

Home › Devices › Olympus › Olympus OM-2n

Olympus OM-2nNEW!

Photo: John Nuttall from Hampshire, United Kingdom, CC BY 2.0 · AI-edited (studio background)

OLYMPUS · CAMERA · 1979-1984

Olympus OM-2n

Also called: OM-2N · OM-2N MD · Olympus OM-2N

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 7 sources · 2 item(s) unverified

1979–1984 Olympus OM-2n 35 mm SLR. Almost entirely mechanical: common work is freeing a jammed winder/shutter, replacing light seals and mirror damper pads, fixing the power switch, and removing prism foam before it eats the silvering.[1][2][3][6][4]

5MODS
4WORK
1EXPERIMENTAL
7SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
OM-2N MD1979–1984 n-suffix body1979OM-2N marking engraved next to the model number on the front plate at the rewind lever. 1979 update redesigned the wind-on lever. Power switch selects manual, auto, off, and battery check.[4][1][5][2]
Specs
Auto exposure rangeOM-2N: about 120s to 1/1000s[4]
BatteryListed as 2× LR44 by a seller's battery finder; check the cell type on your body[7]
MechanicsAlmost entirely mechanical body; needs battery for the shutter to fire[2][5]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Free a jammed winder or shutterWorks
RepairDifficulty: mediumOpens caseNo solderingReversible

One documented jam was a loose screw on the rewind shaft under the bottom plate blocking the gear train. Use JIS drivers; opening the top plate can cause more harm than good.[2][1]

Special tools: JIS screwdriver set, pin wrench

Good to know

  • One documented jam was a loose screw on the bottom end of the rewind shaft that stopped a gear; tightening it freed the winder and shutter.[2]
  • The body is almost entirely mechanical, so this fault was not electronic.[2]
  • The bottom plate uses four cross-head screws; use JIS drivers because Phillips can strip the heads.[2][1]
  • Many parts are shared between OM-1, OM-2, OM-3, and OM-4, so guides for one can often apply to another.[2]

⚠ Watch out

  • Opening the top plate caused more harm than good on the documented body (foam, on/off dial, film counter). Think before opening sections that may not be the fault.[2]

Guides:Fixing an Old Film Camera, Part 2: First, Do No HarmFinding and Fixing an Old Film Camera, Part 1

Replace light seals and mirror damper padsWorks
RepairDifficulty: mediumOpens caseNo solderingReversible

Replace door light seals and mirror damper foam before the first film. Match original thickness (about 1 mm on the documented body) and protect the shutter while cleaning.[3]

Special tools: isopropyl alcohol, card scrap to protect shutter

Good to know

  • Replace the light seals, the mirror damper pads, and do basic cleaning before the first film.[3]
  • Keep seal material the same thickness as the original; look up the model for the right thickness (about 1 mm was used on that body).[3]
  • Clean the channel with isopropyl alcohol and tape card over the shutter to protect it.[3]

⚠ Watch out

  • Do not spoil the focusing screen while scraping; keep the mirror and screen untouched where possible.[3]
  • Tuck foam behind the counter-reset switch without blocking its action.[3]

Guides:Fixing an Old Film Camera, Part 3: Fixing the Light Seals and Shooting

Remove prism foamWorks
RepairDifficulty: hardOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

All OM-2N bodies have prism foam that can release acid and dissolve prism silvering. Closest step guide is written for the OM-1; confirm fit before you dig in.[6]

Good to know

  • All OM-2N versions have prism foam installed.[6]
  • As the foam degrades it releases an acidic goo that slowly dissolves the prism silvering — a terminal fault.[6]
  • Remove batteries and set the meter switch to OFF before work.[6]

⚠ Watch out

  • Do not use a spanning wrench or screwdriver in the advance-winder trim slots; the trim is thin.[6]
  • Guide steps are written for the OM-1; OM-2n procedure is not shown separately.[6]

Guides:Olympus OM-1 Prism Foam Removal

Repair the power / mode switchExperimental
RepairDifficulty: hardOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

The switch selects manual, auto, off, and battery check. Misalignment when refitting the top plate can break the internal fork; one repair used plywood tips and superglue.[2][5]

Good to know

  • The switch selects manual, auto, off, and battery-test positions.[2][5]
  • On one body the switch broke when the top was refitted without lining the switch up with the external control; new fork tips were cut and glued.[2]
  • Without a battery the shutter will not fire.[5]

Guides:Fixing an Old Film Camera, Part 2: First, Do No Harm

Fit meter batteriesWorks
BatteryDifficulty: easyCase stays closedNo solderingReversible

A battery finder lists 2× LR44 for the OM-2n. Check the cell type on your body before buying.[7][5]

Parts

  • 2× LR44 Fits with conditions — Listed by a seller's battery finder; cell type not confirmed by a second source.[7] Buy: ausgeknipst.de

Good to know

  • An Olympus battery finder lists the OM-2n as 2× LR44.[7]
  • The power switch includes a battery-check position.[5]

Guides:No guide found yet.

Sources (7)

SOURCES.TXT