★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000147devices tracked

Home › Devices › Onyx › Onyx Boox e-readers

[ device photo ]NEW!

ONYX · E READER · 2014-2024

Onyx Boox e-readers

Also called: Boox · Onyx Boox · Note Air3 C · Go Color 7 · C67ML · AfterGlow 2

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 13 sources · 3 item(s) unverified

Android e-ink tablets from Onyx. Common soft mods are KOReader, Magisk root (model-specific and risky), and the OnyxTweaks Xposed module on Go Color 7. Newer units often have a microSD slot.[13][7][9][3][5]

7MODS
3WORK
3EXPERIMENTAL
13SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Note Air3 C10.3-inch colour note tablet202310.3-inch Kaleido 3 colour E Ink with stylus (4096 levels) and BSR. Sibling B/W Note Air3 has microSD too but no BSR.[3][4][6]
Go Color 71st gen 7-inch colour20247-inch Kaleido 3, Android 12 with Play Store, no stylus. Target device for OnyxTweaks.[5][7]
C67MLC67ML / Carta / Carta2—Three main models: C67ML, C67ML Carta, C67ML Carta2. Android 4.2 era.[1]
AfterGlow 2Arta Tech rebrand of C67ML family—Polish rebrand of the C67ML line; same Android 4.2.2 as C67ML.[1][2]
Specs
Note Air3 C10.3-inch Kaleido 3; 4 GB RAM; 64 GB + microSD; 3700 mAh; Android 12; USB-C with OTG[3][6]
Go Color 7 (1st gen)7-inch Kaleido 3; 2300 mAh; Android 12 with Google Play; microSD; USB-C with OTG; no stylus[5]
C67ML familyAndroid 4.2; microSD up to 32 GB; C67ML 1700 mAh (Carta models 3000 mAh)[1][2]

Mods (7)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

KOReaderWorks
SoftwareDifficulty: easyCase stays closedNo solderingReversible

Install the Android APK for KOReader, an open-source e-ink document viewer. Boox units run Android, but e-ink refresh support in KOReader can lag on newer models.[12][13][11]

Good to know

  • KOReader is a document viewer for E Ink devices (EPUB, PDF, DjVu, and more) and has an Android install path.[12][13]
  • Android packages are architecture-specific APKs; sideload via F-Droid, browser, or ADB. ARM is standard for Android e-ink devices.[13]
  • On Boox Go 10.3 (Sept 2024), KOReader listed the device but e-ink refresh was not yet done in the nightly, even though the Onyx e-ink driver worked.[11]

Guides:Installation on Android devices · KOReader Wiki

Expand storage with microSDWorks
StorageDifficulty: easyCase stays closedNo solderingReversible

Note Air3 C, Go Color 7, and the C67ML family have microSD slots. The C67ML takes cards up to 32 GB.[3][6][5][1]

Good to know

  • Note Air3 C: 64 GB internal plus a microSD / microSDHC slot.[3][6]
  • Go Color 7 has a microSD slot.[5]
  • C67ML takes microSD up to 32 GB.[1]

Guides:No guide found yet.

OnyxTweaks (Xposed)Works
SoftwareDifficulty: hardCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

LSPosed / Xposed module for launcher, status bar, quick settings, and e-ink refresh tweaks. Built and tested on Go Color 7 (1st gen) Android 12 after Magisk root.[7][9][10]

Good to know

  • Tested on Go Color 7 (1st gen); the author cannot guarantee full compatibility with other Boox models.[7]
  • Requires Magisk root, then Zygisk and the LSPosed Magisk module.[7]
  • Tested on firmware 4.0, 4.1, and 4.2.[7]

⚠ Watch out

  • Root comes first; rooting modern Boox units has brick risk (anti-rollback, locked bootloader, EDL recovery).[7][9][10]

Guides:OnyxTweaks (GitHub)

Root Note Air3 C (Magisk via EDL)Experimental
SoftwareDifficulty: expertCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Back up boot partitions over EDL, patch with Magisk, and write them back. Firmware has anti-rollback; bad cables and wrong slot files can brick the unit.[9]

Special tools: EDL cable, ADB / fastboot tools

Good to know

  • Build report for Note Air3 C firmware 4.2: back up boot over EDL, Magisk-patch, write back over EDL.[9]
  • Boox firmware implements anti-rollback protection, so older firmware may not boot again.[9]
  • Many cables marketed as EDL cables do not work properly.[9]

⚠ Watch out

  • Keep track of which patched file goes to which slot. A failed attempt left a unit stuck at the logo until recovered on 4.2.[9]

Guides:Rooting Onyx Boox Note Air3C - MobileRead

Root Go 7 (B/W)Experimental
SoftwareDifficulty: expertCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Community attempts to Magisk-patch boot on the Go 7 (B/W). Stock bootloader is locked; Magisk-patched images often fail to boot; EDL may be the only recovery path.[10]

Special tools: EDL cable, ADB / fastboot tools

Good to know

  • One thread reports Magisk-patched boot images do not boot on the Go 7, regardless of method.[10]
  • Once stuck in fastboot, an EDL cable was described as the only way back in.[10]
  • A later post claims the Go 7 (B/W) was rooted; this is unconfirmed.[10]

Guides:No guide found yet.

Root C67ML / AfterGlow 2Experimental
SoftwareDifficulty: hardCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

2015 reports say AfterGlow 2 and C67ML can be rooted. The method is unverified.[2]

Good to know

  • AfterGlow 2 and C67ML can be rooted; both ran Android 4.2.2.[2]
  • Modifying the device takes skill; bricking is easy.[2]

Guides:No guide found yet.

Legacy Xposed Boox tweaks (stale)Discontinued
SoftwareDifficulty: hardCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.

Older Xposed module (navigation bar and system fixes) marked stale; may not work on recent firmware. Tested only on Max3.[8]

Good to know

  • Project status: stale; may not work with recent firmware.[8]
  • Using this module could cause harm to your device.[8]

Guides:xposed-boox-tweaks-and-fixes (GitHub)

Sources (13)

SOURCES.TXT