★ 177 device pages approved★ 2146 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 177 device pages approved★ 2146 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000183devices tracked

Home › Devices › Palm › Palm Pre

[ device photo ]NEW!

PALM · PHONE · 2009-2010

Palm Pre

Also called: Pre · Palm Pre Plus · webOS Pre · P100UNA · P101UNA

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 19 sources · 3 item(s) unverified

First webOS phone with a slide-out keyboard. Homebrew apps install without root via developer mode. iFixit covers battery, screen and keyboard. LuneOS does not list the Pre as supported.[1][6][12][4]

6MODS
4WORK
1EXPERIMENTAL
19SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
P100UNAPalm Pre (Telcel)2009Original Pre: center button, 8 GB storage, 1150 mAh pack. Slide-out QWERTY.[1][17][13]
P101UNAPalm Pre Plus2010Pre Plus: no center button, 16 GB storage, 512 MB RAM, built-in Touchstone compatibility. US Verizon launch January 25, 2010.[1][16]
Specs
Storage (original Pre)8 GB internal; no memory card slot[1]
Battery1150 mAh removable lithium-ion[1][13]
Audio3.5 mm headphone jack[1]
ChargingmicroUSB; optional Touchstone induction dock[1]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Homebrew apps (no root)Works
SoftwareDifficulty: easyCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Enable developer mode, then install third-party .ipk apps over USB with WebOSQuickInstall / Preware. No root required for the basic route. Firmware updates have closed older sideload holes.[6][7][2][1][9][8]

Good to know

  • WebOSQuickInstall is a Java app that installs and removes third-party apps over USB after developer mode is enabled from the card view.[6][2]
  • Preware’s AutoPatch feed installs and removes packaged homebrew system patches; an Emergency Patch Recovery tool can undo patch changes.[7]
  • webOS Doctor can restore a phone to factory settings after homebrew problems.[2]
  • Firmware 1.0.4 closed an early email sideload loophole and broke some homemade apps.[9][8]

⚠ Watch out

  • The 2009 install articles are historical; current tool hosts and wiki pages may be gone or blocked. Prefer a verified Preware / webOS Internals path before flashing.[6] unverified

Guides:Getting Started with Palm Pre Homebrew Apps

CPU overclock patchExperimental
SoftwareDifficulty: hardCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.

Community kernel patches ran the Pre (and Pre Plus) at about 720–800 MHz on webOS 1.4. Palm said it would likely void warranty; Engadget called out destroy-the-phone risk.[10][11]

Good to know

  • Hackers showed overclocking a Palm Pre to 720 MHz or 800 MHz. Palm said doing so would probably void the warranty.[10]
  • An 800 MHz patch for webOS 1.4 on Pre and Pre Plus was described as risky and possibly destructive. Creators claimed only a small extra battery drain.[11]

⚠ Watch out

  • Engadget said the 800 MHz patch may destroy the phone, and Palm said overclocking would probably void the warranty.[10][11] unverified

Guides:No guide found yet.

LuneOS / webOS PortsNot possible
SoftwareDifficulty: noneCase stays closedNo solderingReversible

Open-source webOS successor for modern hardware. The Palm Pre, Pre Plus and Pre 2 do not appear on the project’s working or in-progress device lists.[4][3][5]

Good to know

  • LuneOS is the open-source successor to Palm/HP webOS. webOS Ports lists only a small set of devices with working ports.[3][4][5]
  • The Palm Pre, Pre Plus and Pre 2 do not appear in the working or in-progress lists on the webOS Ports homepage.[4]
Battery replacementWorks
BatteryDifficulty: easyOpens caseNo solderingReversible10-15 min
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Snap off the back panel and pull the tab to swap the 1150 mAh pack. Aftermarket 1350 mAh packs were sold that fit the stock frame; one field test saw little runtime gain.[12][13][1][18][19]

Special tools: spudger

Parts

  • 1150 mAh stock-style pack Fits — Original capacity per teardown and Wikipedia.[13][1]
  • 1350 mAh extended pack (Seidio / Kanex era) Fits with conditions — 2009 packs claimed to fit the stock frame. One Kanex review saw almost no runtime gain versus stock.[18][19]

Good to know

  • Power off, snap off the back panel, and carefully pull the tab to remove the battery.[12]
  • Capacity is 1150 mAh. Seidio and Kanex sold 1350 mAh packs that fit the same space; Gear Diary measured almost the same runtime as stock.[13][18][19]

Guides:Palm Pre Battery Replacement

Screen assembly replacementWorks
ScreenDifficulty: hardOpens caseNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Replace the screen for dead pixels or unresponsive touch. Battery out first, then T5 screws and PCB connectors.[14]

Special tools: T5 Torx, spudger

Good to know

  • Remove the battery, then six T5 screws to free the backplate. Two PCB connectors must be disconnected before the board lifts out.[14]

Guides:Palm Pre Screen Assembly Replacement

Keyboard replacementWorks
Buttons & inputDifficulty: mediumOpens caseNo solderingReversible

Replace the slide-out QWERTY. Heavy adhesive joins the keypad board to the sensors; antenna hinge and ribbons come off first.[15]

Special tools: spudger, tweezers, T5 Torx

Good to know

  • Heavy adhesive connects the keypad control board to the keypad sensors, so prying is needed. Antenna hinge and ribbon connectors come off before the keyboard slides out.[15]

Guides:Palm Pre Keyboard Replacement

Sources (19)

SOURCES.TXT