Home › Devices › Palm › Palm Tungsten (T3 / T5 / E2)
PALM · PDA
Palm Tungsten (T3 / T5 / E2)
Also called: Tungsten T3 · Tungsten T5 · Tungsten E2 · PalmOne Tungsten · T|E2
Palm OS PDAs with iFixit guides for the T3 screen and board and the E2 battery, optional SDIO Wi-Fi, and a community flash-storage firmware for early flash-ROM E2 units.[5][2][1][4][9]
Which one do I have?
| Model | Variant | Year | How to tell |
|---|---|---|---|
| Tungsten T3 | Sliding PDA with wide screen | — | Slider design with 320×480 screen. Stock 900 mAh pack. Early units had an SD-card firmware patch.[5][2] |
| Tungsten T5 | Flash-drive PDA | — | 256 MB with a large flash-drive partition. Uses SDIO for Wi-Fi.[5] |
| Tungsten E2 | Compact Garnet PDA | — | No USB charging. Bluetooth and a standard headphone jack. Serial prefixes PN20U (USA) and PN20M (EFIGS). Flash-ROM vs mask-ROM chips decide if de-NVFS firmware can run.[6][4][5] |
Specs
Mods (6)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Replace the E2 batteryWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
- ⚠ Data loss Can erase what is on the device. Back up first.
Four Torx T5 back screws, unplug the pack connector, fit a new cell, charge fully and reset.[1]
Special tools: Torx T5
Good to know
Replace the T3 / T5 batteryExperimental
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
- ⚠ Data loss Can erase what is on the device. Back up first.
Aftermarket Li-polymer cells are sold for the T3 family and T5. Sync before opening.[13][12][3][5]
Parts
- BatteryWeb 3.7 V 1100 mAh (M550 / T3 family) Fits with conditions — Listed for M550, T1, T2 and T3 replacing IA1TA16A0. Shop claim; Wikipedia stock T3 is 900 mAh.[13][5] Buy: batteryweb.com
- BatteryWeb 3.7 V 1350 mAh (T5) Fits with conditions — Listed as replacing OEM IA1XA27F1. Shop claim only.[12] Buy: batteryweb.com
Good to know
- The T3 shipped with a 900 mAh battery; third-party 1100 or 1150 mAh cells exist (Wikipedia marks this citation needed).[5]
- On the T3 motherboard guide, the battery joins the board with red and black cables; be gentle so the port is not damaged.[3]
- The T5 and M550 power RAM from the main cell, so sync before removing the old pack (shop advice).[12][13]
⚠ Watch out
Guides:No guide found yet.
Replace the T3 screenWorks
Open the back and slider assembly, then swap the 320×480 panel.[2][7]
Good to know
- iFixit rates the T3 screen guide Moderate and marks it as needing better images.[2]
- Remove any memory card first. Press the centre indentation to free the back cover.[2]
- The buttons and sliding tray stay attached by an orange cable. The screen cable disconnects by pulling upward from the lower right of the motherboard.[2]
⚠ Watch out
- Digitizer drift on the T3 may survive a connector reseat; one teardown diary could not fix drift that way.[7]
E2 flash-storage firmware (de-NVFS)Experimental
- ⚠ Can brick A mistake can leave the device unable to start.
- ⚠ Data loss Can erase what is on the device. Back up first.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
On early flash-ROM E2 units, community firmware turns the flash into card-like storage and changes RAM split. Mask-ROM units cannot be flashed.[4]
Good to know
- After flashing, the device has 9 MB storage RAM and 6 MB program RAM.[4]
- Only some pre-2006 E2 units have a writable flash-ROM chip; later units use read-only mask ROM.[4]
- Open the device: an Intel flash chip can be flashed; a chip marked MX cannot.[4]
- 2005 E2 units are more likely to have flash-ROM. USA serial prefix PN20U; EFIGS prefix PN20M.[4]
Guides:de-nvfs [Palm OS Wiki]
SDIO Wi-Fi cardDiscontinued
palmOne's SD Wi-Fi card plus period drivers added wireless to the T3, T5 and E2. The cards and drivers are historical.[5][9][10][11]
Good to know
- The T3, T5 and E2 gain Wi-Fi only through the optional SDIO Wi-Fi card.[5]
- In 2004 palmOne released a T5 driver update for its SD Wi-Fi card; Engadget said the card already worked on the T3 and Zire 72.[9][11]
- In 2005 a driver let the E2 use the same palmOne Wi-Fi SD card.[10]
Guides:No guide found yet.
Headphone hole in hard case (E2)Works
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Cut a hole in a Palm hard case with a rotary tool so the E2 headphone plug clears when the case closes.[8]
Special tools: rotary tool
Good to know
Sources (13)
- docs Palm Tungsten E2 Battery Replacement · 2026-11-17
- docs Tungsten T3 Screen Replacement · 2026-11-17
- docs Tungsten T3 Motherboard Replacement · 2026-11-17
- wiki de-nvfs [Palm OS Wiki] · 2026-11-17
- wiki Palm Tungsten - Wikipedia · 2026-11-17
- blog Palm/Tungsten/E2 - Tao of Mac · 2026-11-17
- blog Taking My Tungsten T3 Apart · 2026-11-17
- docs Palm Tungsten case mod - Make: · 2026-11-17
- news palmOne releases SD WiFi card driver for the Tungsten T5 · 2026-11-17
- news Use palmOne's WiFi SD card with the Tungsten E2 · 2026-11-17
- news PalmOne Releases Wi-Fi Drivers for Tunsten T3, T5 · 2026-11-17
- shop Palm Tungsten T5 Replacement Battery · 2026-11-17
- shop Palm M550 Replacement Battery (T3 family) · 2026-11-17