★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 200 device pages approved★ 2429 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000206devices tracked

Home › Devices › Palm › Palm Tungsten (T3 / T5 / E2)

[ device photo ]NEW!

PALM · PDA

Palm Tungsten (T3 / T5 / E2)

Also called: Tungsten T3 · Tungsten T5 · Tungsten E2 · PalmOne Tungsten · T|E2

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 13 sources · 2 item(s) unverified

Palm OS PDAs with iFixit guides for the T3 screen and board and the E2 battery, optional SDIO Wi-Fi, and a community flash-storage firmware for early flash-ROM E2 units.[5][2][1][4][9]

6MODS
3WORK
2EXPERIMENTAL
13SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Tungsten T3Sliding PDA with wide screen—Slider design with 320×480 screen. Stock 900 mAh pack. Early units had an SD-card firmware patch.[5][2]
Tungsten T5Flash-drive PDA—256 MB with a large flash-drive partition. Uses SDIO for Wi-Fi.[5]
Tungsten E2Compact Garnet PDA—No USB charging. Bluetooth and a standard headphone jack. Serial prefixes PN20U (USA) and PN20M (EFIGS). Flash-ROM vs mask-ROM chips decide if de-NVFS firmware can run.[6][4][5]
Specs
T3 memory / screen64 MB (52 MB usable); 3.7-inch 320×480; stock 900 mAh battery[5]
T5 memory256 MB with 161.2 MB configured as a flash drive[5]
E2Palm OS Garnet 5.4.7; 200 MHz XScale; NVFS flash; SD cards up to 1 GB[5]
Wi-FiOptional SDIO Wi-Fi card on T3, T5 and E2 (no built-in radio)[5]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Replace the E2 batteryWorks
BatteryDifficulty: mediumOpens caseNo solderingReversible15 min
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Four Torx T5 back screws, unplug the pack connector, fit a new cell, charge fully and reset.[1]

Special tools: Torx T5

Good to know

  • iFixit rates the community E2 guide Moderate, about 15 minutes.[1]
  • After install, charge the new battery fully, press reset, and set the date and time again.[1]

Guides:Palm Tungsten E2 Battery Replacement

Replace the T3 / T5 batteryExperimental
BatteryDifficulty: mediumOpens caseNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Aftermarket Li-polymer cells are sold for the T3 family and T5. Sync before opening.[13][12][3][5]

Parts

  • BatteryWeb 3.7 V 1100 mAh (M550 / T3 family) Fits with conditions — Listed for M550, T1, T2 and T3 replacing IA1TA16A0. Shop claim; Wikipedia stock T3 is 900 mAh.[13][5] Buy: batteryweb.com
  • BatteryWeb 3.7 V 1350 mAh (T5) Fits with conditions — Listed as replacing OEM IA1XA27F1. Shop claim only.[12] Buy: batteryweb.com

Good to know

  • The T3 shipped with a 900 mAh battery; third-party 1100 or 1150 mAh cells exist (Wikipedia marks this citation needed).[5]
  • On the T3 motherboard guide, the battery joins the board with red and black cables; be gentle so the port is not damaged.[3]
  • The T5 and M550 power RAM from the main cell, so sync before removing the old pack (shop advice).[12][13]

⚠ Watch out

  • Sync before battery work. T5/E2 NVFS keeps files when the battery drains, but the shop still warns that RAM is powered by the main cell.[12][13][5]

Guides:No guide found yet.

Replace the T3 screenWorks
ScreenDifficulty: mediumOpens caseNo solderingReversible

Open the back and slider assembly, then swap the 320×480 panel.[2][7]

Good to know

  • iFixit rates the T3 screen guide Moderate and marks it as needing better images.[2]
  • Remove any memory card first. Press the centre indentation to free the back cover.[2]
  • The buttons and sliding tray stay attached by an orange cable. The screen cable disconnects by pulling upward from the lower right of the motherboard.[2]

⚠ Watch out

  • Digitizer drift on the T3 may survive a connector reseat; one teardown diary could not fix drift that way.[7]

Guides:Tungsten T3 Screen Replacement

E2 flash-storage firmware (de-NVFS)Experimental
SoftwareDifficulty: hardCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

On early flash-ROM E2 units, community firmware turns the flash into card-like storage and changes RAM split. Mask-ROM units cannot be flashed.[4]

Good to know

  • After flashing, the device has 9 MB storage RAM and 6 MB program RAM.[4]
  • Only some pre-2006 E2 units have a writable flash-ROM chip; later units use read-only mask ROM.[4]
  • Open the device: an Intel flash chip can be flashed; a chip marked MX cannot.[4]
  • 2005 E2 units are more likely to have flash-ROM. USA serial prefix PN20U; EFIGS prefix PN20M.[4]

Guides:de-nvfs [Palm OS Wiki]

SDIO Wi-Fi cardDiscontinued
ConnectivityDifficulty: easyCase stays closedNo solderingReversible

palmOne's SD Wi-Fi card plus period drivers added wireless to the T3, T5 and E2. The cards and drivers are historical.[5][9][10][11]

Good to know

  • The T3, T5 and E2 gain Wi-Fi only through the optional SDIO Wi-Fi card.[5]
  • In 2004 palmOne released a T5 driver update for its SD Wi-Fi card; Engadget said the card already worked on the T3 and Zire 72.[9][11]
  • In 2005 a driver let the E2 use the same palmOne Wi-Fi SD card.[10]

Guides:No guide found yet.

Headphone hole in hard case (E2)Works
CaseDifficulty: easyCase stays closedNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Cut a hole in a Palm hard case with a rotary tool so the E2 headphone plug clears when the case closes.[8]

Special tools: rotary tool

Good to know

  • An unmodified Palm hard case will not close with earphones plugged into the E2.[8]
  • The write-up cuts a hole in the case with a Dremel.[8]

Guides:Palm Tungsten case mod - Make:

Sources (13)

SOURCES.TXT