★ 215 device pages approved★ 2630 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 215 device pages approved★ 2630 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000221devices tracked

Home › Devices › Pentax › Pentax K10D

[ device photo ]CUSTOM FW!

PENTAX · CAMERA

Pentax K10D

Also called: K10D · Pentax K10D digital SLR

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 13 sources · 6 item(s) unverified

A 10-megapixel Pentax K-mount SLR. Owners install the official firmware, swap the viewfinder screen, and some people convert the sensor for infrared.[1][3][5][8]

5MODS
4WORK
1EXPERIMENTAL
13SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearFirmwareHow to tell
K10D10.2-megapixel digital SLR—1.31The body is marked K10D. Turn it on while holding MENU to read the firmware version on the rear screen.[1][3]
Specs
Sensor10.2 megapixel effective CCD, 23.5 × 15.7 mm[1]
Screen2.5-inch TFT color LCD, about 210,000 pixels[1]
ViewfinderGlass pentaprism, 95% coverage, 0.95× with a 50mm f/1.4[1][5]
StorageSD and SDHC[1]
BatteryD-LI50 lithium-ion; optional D-BG2 grip uses the same battery[1][2]
USBUSB 2.0 HI-SPEED[1]
Audio jacksNo microphone jack and no headphone jack[13]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Official firmware 1.31Works
SoftwareDifficulty: noneCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

The maker's last update is version 1.31. It improves recording on some SDHC cards and adds earlier fixes, including SDM lenses and computer control.[3]

Good to know

  • Firmware 1.31 was released on 22 April 2010. It improves recording stability with some SDHC cards.[3]
  • Version 1.30 adds support for Pentax DA lenses with the SDM supersonic motor. Version 1.20 adds PENTAX REMOTE Assistant 3. Version 1.10 adds wireless control of an external flash and ISO changes from a dial.[3]
  • The updater applies to firmware 1.00, 1.10, 1.11, 1.20, and 1.30. Windows and Mac downloads are posted.[3]
  • The update uses a blank formatted SD card of at least 16 MB, a full D-LI50 battery, and the file fwdc162.bin in the root of the card.[3]

⚠ Watch out

  • Read the readme in the download before you update.[3]
  • Only K10D owners are allowed to download the update.[3]

Guides:Latest K10D firmware update

Computer control over USBWorks
ConnectivityDifficulty: noneCase stays closedNo solderingReversible

PENTAX REMOTE Assistant 3 runs the K10D from a Windows PC over USB and saves pictures to the computer. The camera needs firmware 1.20 or later.[4][3]

Good to know

  • Version 3.51, released 28 May 2008, controls the K10D over USB. Pictures are saved on the computer. It also offers interval, timer, and bulb-timer modes, and it supports more than two connected cameras.[4]
  • The K10D needs firmware 1.20 or later. The listed operating systems are Windows XP and Windows Vista.[4]
  • On Windows Vista, start the program with Run as administrator.[4]

⚠ Watch out

  • Only K10D and K20D owners are allowed to download this software.[4]

Guides:PENTAX REMOTE Assistant 3 for the K10D

Replace the focusing screenWorks
OpticsDifficulty: easyCase stays closedNo solderingReversible

The viewfinder screen is interchangeable. Pentax offered a grid screen and a scaled screen in place of the plain matte screen.[5][1][11]

Special tools: tweezers

Parts

  • LL-80 AF Cross-Lined Matte Fits — Optional screen with vertical and horizontal lines for horizons and buildings.[5]
  • LI-80 AF Scaled Matte Fits — Optional screen with scales for comparing size, including moon photos.[5]

Good to know

  • The focusing screen is interchangeable. The standard screen is the LF-80 Natural-Bright-Matte, also listed as the Natural-Bright-Matte II.[5][1]
  • An LL-80 fitted at a shop was a quick job. The screen comes with instructions and tweezers. Another owner swapped an LL-80 at home with the included tool and the instructions.[11]

⚠ Watch out

  • Dust that settles on the screen shows in the viewfinder. Do the swap somewhere as dust-free as you can.[11] unverified

Guides:No guide found yet.

Autofocus correction in the service menuExperimental
SoftwareDifficulty: noneCase stays closedNo solderingReversible

A hidden service menu on firmware 1.10 can shift autofocus. The shift applies to every lens, not one lens at a time.[12]

Good to know

  • On firmware 1.10, a button sequence opens a service menu with an AF test. Front focus is reduced by lowering the value. Back focus is reduced by raising it. The same steps turn the menu off again.[12] unverified
  • The correction applies to every lens. A K20D can store a correction per lens. This menu cannot.[12] unverified

⚠ Watch out

  • The posted steps require firmware 1.10. A later reply says the menu will not open on newer firmware unless separate software is used.[12] unverified
  • The posted steps say any use is at your own risk. A wrong value throws off focus for every lens.[12] unverified

Guides:Debug mode on the K10D

Infrared sensor conversionWorks
OpticsDifficulty: hardOpens caseBasic solderingPermanent30 min
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Stored charge Capacitors keep a dangerous charge after the device is off.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

A shop or a careful home job replaces the sensor's hot-mirror filter so the camera records infrared or full spectrum. The body has to come apart, and wires are unsoldered.[7][8][9][10][6]

Special tools: soldering iron, capacitor discharge tool, hex screwdriver

Parts

  • Kolari Vision infrared or full-spectrum conversion Fits — Mail-in service for the K10D. Dust reduction is disabled, and autofocus is calibrated to the 18-55mm kit lens unless you send another lens.[7] Buy: kolarivision.com
  • 1 mm replacement filter Fits with conditions — The stock IR-cut filter is 1 mm thick. A 2 mm filter does not match that space.[9]

Good to know

  • The conversion replaces the internal hot-mirror filter with a glass infrared or clear filter. Listed choices are 550 nm, 590 nm, 665 nm, 720 nm, 850 nm, and full spectrum.[7]
  • Dust reduction is disabled after the shop conversion. Shake reduction still works. Autofocus is calibrated to the Pentax 18-55mm kit lens and is generally accurate for most lenses from 18 mm to 300 mm.[7]
  • You can send your own lens for calibration. If the shop calibrates an ultra-wide lens, autofocus will not work with telephoto lenses.[7]
  • A written home guide rates the job hard, 13 steps, about 30 minutes. It unsolders wires, and it tells you to work grounded.[8]
  • One home conversion desoldered the main board and lifted off the sensor block, which also holds the shake-reduction motors. The IR-cut filter was held by a clip and an adhesive foam gasket, and it was 1 mm thick.[9]
  • The K10D has no live view. A filter on the lens means focus by shooting, adjusting, and shooting again. A filter on the sensor keeps autofocus, but that autofocus has to be adjusted.[10]

⚠ Watch out

  • High chance of cut cables, soldering damage, or static damage. Most conversion companies will not work on Pentax cameras.[8]
  • A capacitor discharge tool is marked optional but recommended. A grounding strap is recommended.[8]
  • Opening the body voids the warranty.[9]
  • The body has seals on 72 parts, including buttons, dials, and seams. The home guide removes screws under the rubber covers.[6][8]
  • If the camera cannot reach infinity focus after conversion, fit a Kolari clear magnetic clip-in filter. Calibrating only an ultra-wide lens drops autofocus on telephotos.[7]

Guides:Pentax K10D infrared conversion DIY tutorial

Buttons & modes

BUTTONS.TXT
WhatHow
Show firmware versionTurn the camera on while holding MENU. The version appears in the center of the rear screen.[3]

Sources (13)

SOURCES.TXT
  1. official K10D specifications · 2026-11-17
  2. official K10D accessories · 2026-11-17
  3. official Latest K10D firmware update · 2026-11-17
  4. official PENTAX REMOTE Assistant 3 for the K10D · 2026-11-17
  5. official K10D interchangeable focusing screens · 2026-11-17
  6. official K10D weather seals · 2026-11-17
  7. shop Pentax DSLR infrared conversion service · 2026-11-17
  8. docs Pentax K10D infrared conversion DIY tutorial · 2026-11-17
  9. docs Converting a Pentax K10D to IR photography · 2026-11-17
  10. news DSLR infrared camera conversion · 2026-11-17
  11. forum Focusing screen for K10D · 2026-11-17
  12. forum Debug mode on the K10D · 2026-11-17
  13. news Pentax K10D review specifications · 2026-11-17