★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000147devices tracked

Home › Devices › Teenage Engineering › Pocket Operator (PO-series)

[ device photo ]NEW!

TEENAGE ENGINEERING · INSTRUMENT · 2015

Pocket Operator (PO-series)

Also called: PO-32 · PO-32 tonic · PO-20 · PO-20 arcade · Teenage Engineering PO

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 15 sources · 3 item(s) unverified

Credit-card synthesizer/sequencers that run on two AAA cells and ship without a case. Common work is arcade-button enclosures, LiPo or USB power, MIDI/USB add-ons, and Eurorack adapters. Official guides cover PO-32 tonic and PO-20 arcade; many mods apply across the PO line.[1][3][5][9]

7MODS
4WORK
3EXPERIMENTAL
15SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
PO-32tonic—Programmable drum and percussion synthesizer/sequencer. Microtonic VST sound transfer (four-channel limit). Built-in mic — leave space for it in arcade builds.[1][2][12][5]
PO-20arcade—Arcade synthesizer and sequencer. Same two-AAA power and sold-without-casing notice as PO-32. Listed as a Eurorack DIY conversion target.[3][7]
Specs
PowerTwo AAA (do not mix alkaline, carbon-zinc, and rechargeable types); unit needs about 3 V[1][3][5]
I/OBuilt-in speaker/mic (model-dependent); line in/out; sync levels should not exceed 5 Vpp[1]

Mods (7)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Arcade-button controller enclosureWorks
Buttons & inputDifficulty: hardCase stays closedBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Wire arcade buttons to the PO pads, relocate pots to a panel, and optionally add audio jacks and a LiPo pack. No custom PCB or code. Permanent if pots are cut from the board.[5][1][4]

Special tools: soldering iron, hot glue or Sugru

Parts

  • 3.7 V 500 mAh LiPo + micro LiPo charger Fits with conditions — Optional rechargeable path in the DJTT build; a 1N4001 diode drops voltage toward the PO’s 3 V need.[5]

Good to know

  • Each arcade button signal wire goes to the matching PO signal pad. No circuit board or coding required.[5]
  • On a PO-32, leave space for the built-in mic.[5]
  • Pots can be cut from the PO and moved to panel mounts (insulate cut pins). A button to ground and the external speaker pad creates a beat-repeat effect; a headphone jack disables that hack.[5]

⚠ Watch out

  • Altering the unit without TE consent voids the warranty. Cover joints so wires cannot short.[1][4][5]
  • Rechargeable batteries are not covered by TE’s warranty.[4]

Guides:DIY: Build An Arcade Controller For Pocket Operators

USB / battery-eliminator powerWorks
ChargingDifficulty: mediumCase stays closedBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Run the PO from USB or a power bank without (or instead of) AAA cells. Options range from a non-modifying 5 V→3 V PSU board to the Pocket Integrator’s battery eliminator.[11][9][8]

Good to know

  • PO-PSU: 5 V in, 3 V out, about 300 mA max; roughly 30 mA RMS per PO. Designed not to modify the PO.[11]
  • Pocket Integrator includes a battery eliminator plus USB MIDI clock out, extra sync, and a digital shaker; mounts with pogo pins, an audio cable, and rubber bands.[9][8]

⚠ Watch out

  • Fitting both of the PO-PSU's optional zero-ohm resistors (R4 and R5) can damage the USB port.[11]

Guides:No guide found yet.

Rechargeable Li-ion battery boardExperimental
BatteryDifficulty: mediumCase stays closedBasic solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Third-party PCB that replaces AAA cells with a protected Li-ion pack and USB charging. Out of stock when checked.[14][4]

Parts

  • Hammerhead Battery Mod (PCB only) Fits with conditions — Fits Pocket Operators generally. Battery sold separately; must include protection circuitry. Nominal 3.7 V, 400–1800 mAh recommended.[14] Buy: tindie.com

Good to know

  • Replaces standard AAA batteries with a rechargeable lithium-ion battery and USB charging.[14]

⚠ Watch out

  • Batteries must include protection circuitry. Rechargeable packs are not covered by TE warranty.[14][4]

Guides:No guide found yet.

Eurorack PO adapterWorks
CaseDifficulty: mediumCase stays closedBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

LPZW adapter holds a Pocket Operator in a Eurorack case with bus power, front I/O, clock division, and an output amp. PO-20 Arcade is listed as a DIY Eurorack conversion.[6][7]

Parts

  • LPZW PO-Series Adapter V2.0 Fits with conditions — Holds a PO in Eurorack; five functions including bus power and I/O. The maker offers a build manual.[6] Buy: leipzigwest.org

Good to know

  • Adapter functions: hold the PO in the rack, bus power, front I/O jacks, clock division, output amp.[6]
  • ModularGrid lists a Eurorack-converted PO-20 Arcade as DIY-only, 12 HP, 12 mm deep.[7]

Guides:No guide found yet.

MIDI / USB-MIDI add-onExperimental
ConnectivityDifficulty: hardCase stays closedBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Commercial MIDI adapters and DIY USB-MIDI projects exist for Pocket Operators. Knobs are usually not MIDI-controllable. The shop adapter is sold out; DIY needs soldering.[15][10][9][12][4]

Parts

  • Hanz Tech MIDI Adapter V3 Fits with conditions — Listed for Pocket Operators generally. No MIDI control of the two knobs. Sold out since March 2025 when checked.[15] Buy: tindie.com

Good to know

  • DIY USB MIDI project: solder wires to the PO; demo was on a PO-14. Unit still plays normally after the mod.[10]
  • Pocket Integrator also provides USB MIDI clock out and a USB→SWD interface for alternate firmware experiments.[9]
  • PO-32 hardware cannot take MIDI in (Microtonic developer reply).[12]

⚠ Watch out

  • Installing non-TE firmware may cause irreversible changes and is not covered by warranty.[4]

Guides:No guide found yet.

FX / WRITE switch hack (PO-32)Experimental
Buttons & inputDifficulty: hardCase stays closedBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Demo of external switches for FX and WRITE on a PO-32 (beat-repeat style control).[13]

Good to know

  • Demo uses switches for FX and WRITE; described as a janky demo of an earlier PO-12 mod.[13]

Guides:No guide found yet.

Official pro caseWorks
CaseDifficulty: easyCase stays closedNo solderingReversible

TE optional pro case mounts after removing the break-away hanger and folding stand. Units ship without casing.[1][3]

Good to know

  • Mount the optional pro case after removing the break-away hanger and folding stand.[1]
  • PO-32 and PO-20 are sold without casing.[1][3]

Guides:PO-32 guide - teenage engineering

Sources (15)

SOURCES.TXT