★ 231 device pages approved★ 2829 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 231 device pages approved★ 2829 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000237devices tracked

Home › Devices › Tiger Electronics › Pokémon Pikachu talking plush

[ device photo ]NEW!

TIGER ELECTRONICS · OTHER · 1999

Pokémon Pikachu talking plush

Also called: Tiger Electronics Pikachu · talking Pikachu plush · Hasbro Pikachu plush 1999

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 9 sources · 4 item(s) unverified

A soft talking Pikachu plush with a built-in voice chip. People circuit-bend Pikachu toys for pitch and body-contact effects, and one builder put a rechargeable Li-ion pack and LEDs under the skin.[1][2][6]

2MODS
0WORK
2EXPERIMENTAL
9SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Tiger Electronics talking Pikachu plush1999 Hasbro-distributed plush1999About 20 cm soft polyester Pikachu that talks when touched. Developed by Tiger Electronics and launched in 1999; Hasbro distributed it.[1]
Specs
SizeAbout 20 cm high, soft polyester[1]
Power2 × AA[1]
SoundBuilt-in electronic voice chip; speaks when touched[1]

Mods (2)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Circuit-bent pitch and body contactsExperimental
AudioDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Open the voice board and add a pitch knob and touch contacts so the toy's voice changes pitch or responds to skin contact.[2][4][3][5][9][8][7]

Good to know

  • Bent Pikachu toys with touch contacts and a pitch knob have been shown since at least 2006.[2]
  • Groups of modded Pikachu toys have been bent together as an "orchestra," and other heavily bent Pikachu builds exist.[4][3][5]
  • A common pitch bend replaces the clock resistor with a potentiometer; 470K is a usual starting value on toy boards.[9] unverified
  • Body contacts are metal points wired to the board; more skin on the contact gives a stronger effect.[9] unverified

⚠ Watch out

  • Bending is done without a schematic by bridging board points and listening. Bending can occasionally produce a puff of smoke.[7][8]
  • Stay on battery power. Guides recommend battery-powered toys, not mains equipment.[7]

Guides:No guide found yet.

Rechargeable Li-ion pack and LEDsExperimental
BatteryDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace the stock cells with a Li-ion pack under the skin, add a cutoff switch and charging ports, and wire tail LEDs from the board.[6]

Parts

  • Adafruit Lithium Ion Battery Pack 6600 mAh Fits with conditions — One build planned three packs in parallel with a cutoff switch.[6]

Good to know

  • One builder put a Li-ion pack with charging ports and a cutoff switch under a Pikachu plush's skin. The plan was three 6600 mAh packs in parallel.[6]
  • That plush already had LEDs, buttons, an MCU, and a speaker. Tail LEDs were common-anode; grounding one wire turns an LED on.[6]
  • LEDs driven through 2.2K resistors were too dim; the builder suggested 470 ohm instead. Hot glue alone did not hold the LEDs until they were sewn in.[6]

⚠ Watch out

  • Soldering on the light fabric can burn it. Sew LED mounts; do not rely on hot glue alone.[6]

Guides:No guide found yet.

Sources (9)

SOURCES.TXT