Home › Devices › Polaroid › Polaroid instant camera
POLAROID · CAMERA
Polaroid instant camera
Also called: thermal Polaroid · Sonar Autofocus 5000 · Polaroid Pronto
Box Polaroids have been gutted and rebuilt as thermal cameras: a Raspberry Pi Zero, a small camera, and a receipt printer sit in the original shell and print on thermal paper.[1][3][4]
Which one do I have?
| Model | Variant | Year | How to tell |
|---|---|---|---|
| Sonar Autofocus 5000 | 2018 thermal-printer donor | — | Box body with a sonar transducer beside the lens. The shell is held by plastic tabs, released with a flat screwdriver behind the front panel. The film-door contacts originally met the battery inside an SX-70 film pack.[4][1] |
| Pronto | 2020 thermal-printer donor | — | A box Polaroid. One write-up of the 2020 thermal build names a Pronto from eBay as the donor body.[7] unverified |
Mods (1)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Thermal-paper camera in the shellExperimental
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Remove the film path and fit a Raspberry Pi Zero, a small camera, and a thermal receipt printer. The outside still looks like the Polaroid, and the original shutter button takes the picture.[1][2][3][4][5][6][7]
Special tools: flat screwdriver, mini-drill, Dremel, soldering iron
Parts
- Raspberry Pi Zero or Pi Zero W Fits with conditions — The 2018 build uses a Pi Zero. The 2020 build uses a Pi Zero W for Wi-Fi.[1][3]
- Small USB webcam Fits with conditions — Used in the 2018 build. The printer is only 384 pixels wide, so a sharper camera does not improve the print.[1][6]
- Raspberry Pi camera module Fits with conditions — Used in the 2020 build, with the Pi camera preview mode left running to cut shutter lag.[3]
- Compact thermal receipt printer Fits with conditions — The 2018 build uses the smallest printer found, over USB or serial. Its Bluetooth radio is not used. Its 7.4 V lithium-ion pack also powers the Pi through a 5 V step-down.[1]
- Thermal print head and driver board Fits with conditions — The 2020 build uses a receipt-printer head and driver board, powered by two 3000 mAh LiPo cells in series.[3]
Good to know
- The 2018 camera is a Pi Zero, a USB webcam, and a thermal printer inside a Sonar Autofocus 5000. The original shutter button stays.[1][4]
- That shell has almost no screws, apart from one bolt on the shutter solenoid. Tabs behind the front panel release with a flat screwdriver. The new build solders USB pairs, a transceiver chip, and the printer battery leads.[1]
- A stock boot took about 40 seconds before a picture. The JPEG sits in a tmpfs /tmp so the SD card is written less.[1]
- A custom buildroot image cuts boot to about 2 seconds. The HDMI splash is disabled, and kernel messages stay off the serial port.[6]
- The webcam sits behind the autofocus ring. The ring's thread does not match the webcam, so focus is not linked. The sensor's depth of field is deep enough that focus barely matters.[2]
- The image path is a C++ step that turns a YUYV frame into a JPEG, then a Python step that resizes, dithers, and adds the printer header.[2]
- A hard switch cuts the 7.4 V pack completely, so there is no standby drain. The pack does not charge while the switch is off.[1]
- The 2020 camera is a Pi Zero W, a Pi camera module, and a thermal head and driver. Two 3000 mAh LiPo cells in series feed the printer. A buck converter makes 5.1 V for the Pi. Typical use is about 12 hours between charges.[3]
- The viewfinder and the original shutter button stay. A 2.5 cm speaker plays a shutter sound. Saved colour files get a date stamp and can be copied off over Wi-Fi. The thermal print is the instant copy.[3]
- High-resolution files also stay on the SD card. A Dremel clears the old film cartridge and the film-drive plastic.[7]
- The paper roll sits on a brass spool with a magnet at each end and holds about 150 photos.[3]
⚠ Watch out
- Cut plastic cannot be put back, and there are no replacement shells. Wear eye and ear protection while cutting.[1]
- If the print head is not lined up with the paper, the paper crumples and jams.[1]
- Getting a clean print took more than a full roll of paper.[6]
- The USB solder joints are fine wires. One builder covered those joints with superglue so they would not flex apart.[1]
- About two-thirds of the 2020 build was cutting plastic with a Dremel, and hoping not to cut too much.[3]
- The 2020 build is not a project for the faint of heart.[5]
Guides:Thermal Paper PolaroidRetrofit a Polaroid camera with a Raspberry Pi and a thermal printer
Buttons & modes
| What | How |
|---|---|
| Shutter | On the 2018 camera, the half-press and the full-press of the original shutter are both kept as inputs.[1] |
Sources (7)
- official Thermal Paper Polaroid · 2026-11-17
- forum Thermal Polaroid forum thread · 2026-11-17
- docs Retrofit a Polaroid camera with a Raspberry Pi and a thermal printer · 2026-11-17
- news This modified Polaroid camera prints photos on thermal paper · 2026-11-17
- news This guy hacked an old Polaroid to print instant photos on thermal paper · 2026-11-17
- news Thermal Paper Polaroid — Raspberry Pi Official Magazine · 2026-11-17
- news Old Polaroid gets a Pi and a printer · 2026-11-17