★ 208 device pages approved★ 2530 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 208 device pages approved★ 2530 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000214devices tracked

Home › Devices › Polaroid › Polaroid instant camera

[ device photo ]NEW!

POLAROID · CAMERA

Polaroid instant camera

Also called: thermal Polaroid · Sonar Autofocus 5000 · Polaroid Pronto

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 7 sources · 1 item(s) unverified

Box Polaroids have been gutted and rebuilt as thermal cameras: a Raspberry Pi Zero, a small camera, and a receipt printer sit in the original shell and print on thermal paper.[1][3][4]

1MODS
0WORK
1EXPERIMENTAL
7SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Sonar Autofocus 50002018 thermal-printer donor—Box body with a sonar transducer beside the lens. The shell is held by plastic tabs, released with a flat screwdriver behind the front panel. The film-door contacts originally met the battery inside an SX-70 film pack.[4][1]
Pronto2020 thermal-printer donor—A box Polaroid. One write-up of the 2020 thermal build names a Pronto from eBay as the donor body.[7] unverified

Mods (1)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Thermal-paper camera in the shellExperimental
Shell reuseDifficulty: hardOpens caseFine solderingPermanent
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Remove the film path and fit a Raspberry Pi Zero, a small camera, and a thermal receipt printer. The outside still looks like the Polaroid, and the original shutter button takes the picture.[1][2][3][4][5][6][7]

Special tools: flat screwdriver, mini-drill, Dremel, soldering iron

Parts

  • Raspberry Pi Zero or Pi Zero W Fits with conditions — The 2018 build uses a Pi Zero. The 2020 build uses a Pi Zero W for Wi-Fi.[1][3]
  • Small USB webcam Fits with conditions — Used in the 2018 build. The printer is only 384 pixels wide, so a sharper camera does not improve the print.[1][6]
  • Raspberry Pi camera module Fits with conditions — Used in the 2020 build, with the Pi camera preview mode left running to cut shutter lag.[3]
  • Compact thermal receipt printer Fits with conditions — The 2018 build uses the smallest printer found, over USB or serial. Its Bluetooth radio is not used. Its 7.4 V lithium-ion pack also powers the Pi through a 5 V step-down.[1]
  • Thermal print head and driver board Fits with conditions — The 2020 build uses a receipt-printer head and driver board, powered by two 3000 mAh LiPo cells in series.[3]

Good to know

  • The 2018 camera is a Pi Zero, a USB webcam, and a thermal printer inside a Sonar Autofocus 5000. The original shutter button stays.[1][4]
  • That shell has almost no screws, apart from one bolt on the shutter solenoid. Tabs behind the front panel release with a flat screwdriver. The new build solders USB pairs, a transceiver chip, and the printer battery leads.[1]
  • A stock boot took about 40 seconds before a picture. The JPEG sits in a tmpfs /tmp so the SD card is written less.[1]
  • A custom buildroot image cuts boot to about 2 seconds. The HDMI splash is disabled, and kernel messages stay off the serial port.[6]
  • The webcam sits behind the autofocus ring. The ring's thread does not match the webcam, so focus is not linked. The sensor's depth of field is deep enough that focus barely matters.[2]
  • The image path is a C++ step that turns a YUYV frame into a JPEG, then a Python step that resizes, dithers, and adds the printer header.[2]
  • A hard switch cuts the 7.4 V pack completely, so there is no standby drain. The pack does not charge while the switch is off.[1]
  • The 2020 camera is a Pi Zero W, a Pi camera module, and a thermal head and driver. Two 3000 mAh LiPo cells in series feed the printer. A buck converter makes 5.1 V for the Pi. Typical use is about 12 hours between charges.[3]
  • The viewfinder and the original shutter button stay. A 2.5 cm speaker plays a shutter sound. Saved colour files get a date stamp and can be copied off over Wi-Fi. The thermal print is the instant copy.[3]
  • High-resolution files also stay on the SD card. A Dremel clears the old film cartridge and the film-drive plastic.[7]
  • The paper roll sits on a brass spool with a magnet at each end and holds about 150 photos.[3]

⚠ Watch out

  • Cut plastic cannot be put back, and there are no replacement shells. Wear eye and ear protection while cutting.[1]
  • If the print head is not lined up with the paper, the paper crumples and jams.[1]
  • Getting a clean print took more than a full roll of paper.[6]
  • The USB solder joints are fine wires. One builder covered those joints with superglue so they would not flex apart.[1]
  • About two-thirds of the 2020 build was cutting plastic with a Dremel, and hoping not to cut too much.[3]
  • The 2020 build is not a project for the faint of heart.[5]

Guides:Thermal Paper PolaroidRetrofit a Polaroid camera with a Raspberry Pi and a thermal printer

Buttons & modes

BUTTONS.TXT
WhatHow
ShutterOn the 2018 camera, the half-press and the full-press of the original shutter are both kept as inputs.[1]

Sources (7)

SOURCES.TXT