★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000147devices tracked

Home › Devices › Polaroid › Polaroid SX-70

[ device photo ]NEW!

POLAROID · CAMERA · 1972-1981

Polaroid SX-70

Also called: SX-70 · SX70 · SX-70 Land Camera · SX-70 Sonar · SX-70 Alpha

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 14 sources · 4 item(s) unverified

Folding SLR instant camera powered by the 6 V cell in each SX-70 film pack. Common mods are a 600-film exposure conversion (capacitor or resistor), a selectable SX-70/600 switch, a Bluetooth replacement mainboard, and rarer whole-camera digital rebuilds.[9][1][2][5][11]

6MODS
3WORK
3EXPERIMENTAL
14SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
SX-70Original / Model 11972Folding chrome-look polysulfone body. Early units had a plain focusing screen; later ones added a split-image rangefinder.[9][8]
SX-70 Model 2Model 2 (manual focus)1974ABS body in Ebony or Ivory, flash-bar socket, mostly Texas Instruments boards. Serial sits on the underside of the top panel above the yellow film-cover button.[9][8][7]
SX-70 Model 3Model 3 (non-SLR)—Not an SLR: viewfinder is cut into the mirror hood instead of through the taking lens.[9]
SX-70 Sonar OneStepSonar autofocus1978Sonar autofocus transducer on the front; focus can be switched to manual. BLE board install leaves the three sonar indicator wires disconnected.[9][5]
SX-70 AlphaAlpha—Listed with Original, Model, and Sonar as compatible with the PolaFold BLE mainboard.[5][6] unverified
Specs
Lens4-element 116 mm f/8 fixed glass; focus to about 10.4 in (26 cm)[9]
Film / powerSX-70 integral packs; 6 V Polapulse cell inside the pack powers the camera[9]
BodyModel 1: glass-filled polysulfone; Models 2 and 3: ABS (Ebony or Ivory)[9]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

600 film exposure conversionWorks
OpticsDifficulty: hardOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Stored charge Capacitors keep a dangerous charge after the device is off.

Change the timing capacitor (Texas Instruments boards) or resistor (Fairchild boards) so the shutter meters for ISO 600 film instead of SX-70 film. Unmodified cameras overexpose 600 packs by about two stops.[1][2][14][8][10]

Special tools: Polaroid screwdriver (1 mm square drive)

Parts

  • Replacement timing capacitor Fits with conditions — Value depends on the measured stock capacitor and electric-eye condition; a single 150 pF swap is common advice but often poor. Fairchild boards need a resistor change instead (stock ~2700 ohm, replacement ~550 ohm in one tester's work).[1][2][14]

Good to know

  • Going from SX-70 film (~100–160 ISO) to 600 film is about two stops; exposure must get two stops faster.[1][8]
  • On TI boards the change is a capacitor; on Fairchild boards it is a resistor.[1]
  • On TI SLR boards, stock capacitors often measure 600, 700, 800, 1000, or 1200 pF; a common rule divides by 4 (clean eye), 5 (hazy), or 6 (opaque).[1]
  • Brooklyn Film Camera's service version solders a new capacitor and leaves the camera unable to shoot SX-70 film afterward.[10]

⚠ Watch out

  • Confirm the solenoid screw is still at its factory position before changing parts; bottoming it out under-exposes by a large amount.[1]
  • Severe electric-eye corrosion can shift exposure by about one stop; clean or account for it before trusting a new value.[1]
  • An SX-70-rated flash with 600 film overexposes; use a 600-rated flash or an ND gel on the Q-light.[1]
  • Flash-equipped models carry high-voltage flash circuitry.[8]

Guides:The ultimate guide to SX-70 600 conversionsSX70 camera 125ASA to 600ASA conversion

Selectable SX-70 / 600 switchWorks
Buttons & inputDifficulty: hardOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Stored charge Capacitors keep a dangerous charge after the device is off.

Add a slide switch so the camera can meter for either SX-70 or 600 film. Needs disassembly, soldering, and a drilled hole for the switch.[2]

Special tools: Polaroid screwdriver (1 mm square drive), 4 mm drill bit

Parts

  • SMD slide switch + 600 capacitor Fits with conditions — Hole template must match the exact SX-70 body variant. Capacitor-only (no switch) is the simpler fallback if you abandon the drill step.[2]

Good to know

  • Finished cameras get a switch that chooses SX-70 or 600 film metering.[2]
  • The openSX70 founder warns the job can seriously damage the camera and needs soldering and disassembly skill.[2]

⚠ Watch out

  • Protect the plastic bellows during reassembly; a puncture ends the camera.[2]

Guides:SX70 camera 125ASA to 600ASA conversion

Bluetooth replacement mainboardWorks
SoftwareDifficulty: hardOpens caseBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Stored charge Capacitors keep a dangerous charge after the device is off.

Swap the stock mainboard for a PolaFold BLE board. Film mode (SX-70 or 600), calibration, and OTA firmware updates are set in the maker's app—no hardware film switch.[5][6]

Parts

  • PolaFold SX70 BLE Board Fits with conditions — Separate boards for Original/Alpha/Model and for Sonar. Soldering required; board damage from shorts is not warrantied.[6][5] Buy: sx70ble-site.pages.dev

Good to know

  • Supports Original, Alpha, Model, and Sonar bodies; 600 vs SX-70 mode is software-only.[5][6]
  • Supports commercial electronic flashes, not original disposable flashbars.[5]
  • A four-pin solenoid must be converted to two pins during install.[5]

⚠ Watch out

  • Use ESD precautions; anti-static gloves are recommended. Test flash wiring on the stock board before deciding method 1 or 2 on manual-focus cameras.[5]
  • Shutter calibration is not a substitute for fixing aging solenoids or other mechanical faults.[5]

Guides:Mainboard Installation Guide — PolaFold

Rechargeable pack powerExperimental
BatteryDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Add a protected rechargeable pack (PolaVolt-style) so the camera is not dependent on the flat cell inside each film pack.[8]

Good to know

  • Adds a rechargeable power source so the camera does not rely on the battery inside the film pack.[8]
  • Bench guide stresses battery safety and a protected-cell checklist for these builds.[8]

Guides:No guide found yet.

openSX70 Arduino mainboardExperimental
SoftwareDifficulty: expertOpens caseFine solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Open-source Arduino-based board that can replace the stock electronics for manual shutter speed, double exposure, B/T modes, and a PC flash connector. Not sold as a product; hobbyist kits and designs only.[3][4]

Good to know

  • openSX70 is an open hardware and software project, not a retail product, and the project says it probably never will be.[3]
  • Listed features include manual shutter speed, double exposure, B and T modes, and a PC flash connector.[3]
  • Board swap is non-destructive but needs special tools; the Alpha-2 design is Arduino-based with a 7-way flex link to the camera.[3][4]

Guides:No guide found yet.

Whole-camera digital conversionExperimental
Shell reuseDifficulty: expertOpens caseBasic solderingPermanent
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Gut a dead SX-70 and rebuild it around a Raspberry Pi Zero W, Pi camera, thin battery, microSD, and a small LCD where the mirror was. Keeps the folding shell look; not a drop-in digital back.[11][12][13]

Good to know

  • One published build used a Pi Zero W, a 2.5 in screen in place of the mirror, a ~3,000 mAh 4 mm pack, microSD, and a charging port in the film bay.[11][12][13]
  • Only fisheye lenses fit the head depth in that build; software (Python/OpenCV) corrected the distortion.[11][13]
  • The builder estimated about eight months of part-time work and dremelled metal from the head for the sensor.[11]

Guides:How I Made a Digital Polaroid SX-70How I turned a dead Polaroid SX-70 into a working digital camera

Sources (14)

SOURCES.TXT