★ 231 device pages approved★ 2829 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 231 device pages approved★ 2829 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000237devices tracked

Home › Devices › Apple › PowerBook 100

[ device photo ]NEW!

APPLE · LAPTOP · 1991

PowerBook 100

Also called: PB100 · Macintosh PowerBook 100 · M1506 · Apple PowerBook 100

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 16 sources · 3 item(s) unverified

Sony-designed 68000 PowerBook (model M1506) with a lead-acid battery and 40-pin 2.5-inch SCSI. Almost every unit needs a capacitor recap; common upgrades replace the Conner drive with BlueSCSI or SCSI2SD flash, and builders make lithium drop-in battery packs.[2][1][6][11][5]

6MODS
5WORK
1EXPERIMENTAL
16SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
M1506PowerBook 1001991Apple model M1506. Order M0567LL/A is the base; M1045LL/A adds the external floppy. Only PowerBook with a lead-acid pack and a 68000 — packs from the 140–180c line do not fit.[1][2][4][3]
Specs
CPU16 MHz Motorola 68000; the only PowerBook with a 68000[1][2]
Display9-inch monochrome passive-matrix; Sharp LM64P791 panel; 640×400[1][10][9]
RAM2 MB on board; one proprietary 70-pin 100 ns PSRAM slot; max 8 MB[1][2]
Storage2.5-inch SCSI (40-pin), adapter required; stock 20 MB or 40 MB; no internal floppy[2][1][10]
BatterySealed lead-acid main pack (unique among PowerBooks); CMOS backup 2× CR2430 (user-replaceable)[1][2][3]
OSSystem 6.0.8L original; supported 7.0.1–7.5.1 and 7.5.3–7.5.5[1]
SoundOne 8-bit mono sound out[1]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Conner sticky bumper tape fixWorks
RepairDifficulty: mediumOpens caseNo solderingReversible30-60 min
  • ⚠ Data loss Can erase what is on the device. Back up first.

Early Conner 2.5-inch SCSI drives park against a rubber bumper that turns to goo. A piece of tape over the bumper can free the heads if the rest of the drive is healthy.[14][2][13][7]

Good to know

  • Nearly every stock PowerBook 100 uses a Conner drive unless it was replaced.[14][2]
  • Early Conner drives have a rubber bumper that turns sticky; a piece of tape over the bumper can get them working again if nothing else is wrong.[14]
  • The bumper that sticks is under the platter — the head rests on it when parked — so the drive must be opened.[13]
  • One 2022 restore taped the bumper and the drive still spun without seeking — tape is not a sure fix.[7] unverified
  • Later Conner drives have no rubber bumper; a dead one of that type is probably just dead.[14]

⚠ Watch out

  • Keep backups of anything important on the drive. Initiator-mode tools can copy a still-working drive to SD.[13]

Guides:No guide found yet.

BlueSCSI / SCSI2SD flash storageWorks
StorageDifficulty: mediumOpens caseNo solderingReversible1-2 hr
  • ⚠ Data loss Can erase what is on the device. Back up first.

Replace the aging Conner SCSI drive with a BlueSCSI, ZuluSCSI, or SCSI2SD board on the internal 40-pin connector (adapter board required).[11][12][2][10][13]

Parts

  • BlueSCSI (STM32 SCSI emulator) Fits with conditions — Needs the 40-pin PowerBook adapter. The adapter was tested in a 520c and did not work in a 145; fit in the PB100 is unconfirmed. Enable termination for internal use; do not seat the ribbon fully on J1.[11][12][2]
  • BlueSCSI PowerBook 40-pin adapter (v1.1) Fits with conditions — Board v1.0 has a power fault; v1.1 is recommended. MacDat lists the PB100 drive connector as 40-pin; check your cable before buying.[12][2]
  • SCSI2SD replacement drive Fits — Documented installed in place of a 40 MB Conner CP2045 in one teardown unit.[10]

Good to know

  • BlueSCSI is an open-source SD-card replacement for old SCSI drives; initiator mode can image a vintage drive to SD.[11][13]
  • MacDat lists ZuluSCSI, BlueSCSI, or similar as the alternative to repairing the Conner bumper.[2]
  • The internal connector is 2.5-inch SCSI (40-pin) and needs an adapter.[2]
  • The 40-pin PowerBook adapter must have termination enabled to work as the internal drive, and the ribbon should not be seated fully on connector J1.[12]

Guides:No guide found yet.

6 MB SRAM expansion (8 MB total)Works
OtherDifficulty: easyOpens caseNo solderingReversible15-30 min

Fill the single proprietary PSRAM slot with a 6 MB card (or modern SRAM module) to reach the 8 MB maximum.[1][2][9][15]

Parts

  • PurpleRAM 6 MB SRAM module (Jurassic Computing) Fits — Compatible with the PowerBook 100 per the seller, who claims lower power use than PSRAM. Cards from other PowerBook models are a different physical size and will not fit.[15][2] Buy: tindie.com

Good to know

  • Stock is 2 MB on board with one 70-pin 100 ns PSRAM slot; cards from other models will not fit.[1][2]
  • RAM can be expanded to 8 MB with a 6 MB module.[9][15]
  • PurpleRAM uses SRAM instead of PSRAM and the seller says it needs no refresh and uses about a third of the power.[15] unverified

Guides:No guide found yet.

SCSI-Ethernet networkingWorks
ConnectivityDifficulty: easyCase stays closedNo solderingReversible30 min

Apple never sold Ethernet for this machine. Plug a SCSI-Ethernet adapter into the HDI-30 port (often powered from ADB) for wired networking; Wi-Fi can ride on top of that.[9][8]

Parts

  • Asante Micro EN/SC (or similar SCSI-Ethernet) Fits — Plugs into the external SCSI port and draws power from the ADB port in the documented build.[9]

Good to know

  • The PowerBook 100 never had Ethernet and Apple never sold an Ethernet option; a SCSI-Ethernet adapter is the practical route.[9]
  • One working build used an Asante Micro EN/SC on the SCSI port with ADB power, then browsed with NCSA Mosaic under System 7.0.1 / 7.1.[9]
  • The external SCSI port is an HDI-30 (30-pin) connector. SCSI Disk Mode is supported; leave it by pressing both buttons on the left side.[8]

Guides:The Wireless PowerBook 100

Recap logic board, LCD, and inverterWorks
RepairDifficulty: hardOpens caseFine solderingPermanent4-8 hr
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Surface-mount electrolytics leak on every unit. Replace the logic-board, LCD, and backlight-inverter caps (tantalum where they fit) to restore a blank or flaky machine.[2][6][7][16]

Good to know

  • Surface-mount electrolytic capacitors leak and affect every PowerBook 100.[2]
  • Replacing the caps on the logic board and LCD usually restores function, but corrosion may remain.[2]
  • Two of three inductors near C20, C25, C26 and C21 can be corroded and are linked to LCD voltage (two are 150 µH).[2]
  • A full write-up rates the job moderate-to-hard and prefers tantalums where available; the backlight inverter has two electrolytics that should be done too.[6]
  • A 2022 restore of a dead blank-screen unit booted after a full recap; sound stayed dead, which the author blamed on two logic-board caps not yet fitted.[7]

⚠ Watch out

  • Recap the inverter board as well as the logic board and LCD. It has two electrolytics, and one owner who recapped all three still reported a dead brightness dial, with no fix posted.[16][6]

Guides:Repair: Apple Macintosh PowerBook 100 "Gotta re-cap 'em all!" | Gough's Tech Zone

Lithium drop-in main batteryExperimental
BatteryDifficulty: hardCase stays closedBasic solderingReversible2-6 hr
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Original SLA cells are out of production. Builders fit Li-Po packs with a custom BMS that still work with the stock charger (with limits).[5][3][4]

Good to know

  • Original lead-acid cells are no longer made, so any rebuild needs new cells or a third-party pack.[3][4]
  • One build used two Li-Po pouch cells (~7.2 V nominal) in place of the four-cell SLA pack.[5]
  • The stock charger cannot fully charge the Li-Po cells to 8.4 V; that build used relays to switch each cell to its own charger under 80 percent.[5]
  • Pulling the power adapter while those cells are on charge cuts all power to the laptop.[5]
  • A custom BMS and Li-Po pack has been sold on eBay by a 68kMLA member.[3] unverified
  • Do not solder lithium cells with an iron — use a spot welder; thermal runaway is the risk.[3]
  • The PowerBook 100 pack is not interchangeable with the NiCad packs used in the 140–180c line.[3][4]

⚠ Watch out

  • Lead-acid cells must be kept charged or they are ruined — do not leave a stock pack discharged in storage.[4]

Guides:Upgrading The PowerBook 100 With A Fresh New Battery | Hackaday

Buttons & modes

BUTTONS.TXT
WhatHow
SCSI Disk ModeSupported on the PowerBook 100. Set the SCSI ID in the Portable control panel. Press both buttons on the left side to leave the mode.[8]
Prevent pink LCD splotchRemove the trackball before storing the machine closed so the ball cannot mark the screen.[2]

Sources (16)

SOURCES.TXT