★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000080devices tracked

Home › Devices › Psion › Psion Series 5mx

[ device photo ]NEW!

PSION · PDA

Psion Series 5mx

Also called: Psion 5mx · Series 5mx

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 8 sources

A clamshell PDA with a 36 MHz ARM710T, 16 MB of RAM, and a CompactFlash slot. It runs on two AA cells plus a CR2032 backup. The screen ribbon is prone to cracking; Petervis also covers hinge-wire and battery details. Separate projects add a USB serial cable or a new board in the original case.[8][1][4][7][5]

5MODS
3WORK
2EXPERIMENTAL
8SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Series 5mx16 MB—Faster processor, clearer screen, and updated software versus the Series 5. ARM710T at 36 MHz with 16 MB RAM.[8]
Specs
CPU / RAM32-bit ARM710T at 36 MHz; 16 MB RAM[8]
StorageCompactFlash slot[8]
Power2× AA main; CR2032 backup[8][4]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

AA cells and CR2032 backupWorks
BatteryDifficulty: easyCase stays closedNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Runs on two AA cells. A CR2032 backup keeps RAM alive while you swap the main batteries.[4][8]

Parts

  • 2× AA + CR2032 backup Fits — Main door takes an AA pair; CR2032 is the backup cell.[4][8]

Good to know

  • The Series 5 needs a pair of AA batteries to operate. The CR2032 backup maintains RAM during battery swaps.[4]
  • Computing History lists two AA batteries with a CR2032 backup battery on the 5mx.[8]

Guides:No guide found yet.

Screen cable jumper repairWorks
ScreenDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

The flexible screen cable cracks where it bends in the hinge, which shows up as lines or missing parts of the picture. The fix solders a strip of replacement ribbon across the broken track.[1][2]

Special tools: fine-tipped soldering iron

Good to know

  • The screen ribbon cracks, usually near a hole in the plastic, after years of opening and closing the lid.[1]
  • Opening the 5mx for this repair means removing the main batteries, the backup battery, and three case screws. The broken track is bridged by soldering a strip of replacement ribbon cable across it.[1]
  • On the Series 5 harness, the wider part of the ribbon solders to the LCD; the digitizer side mates with four pads under a metal clip.[2]

⚠ Watch out

  • This is micro-soldering on a cracked flex cable. A fine-tipped iron is required.[1]

Guides:Psion Series 5MX disassembly and screen cable repair

Hinge wire repairWorks
RepairDifficulty: hardOpens caseNo solderingPermanent
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

The Series 5 clamshell uses a pair of hinge wires. Plastic hooks in the base moulding can go brittle under spring tension and need repair.[3]

Good to know

  • The Psion Series 5 has a pair of hinge wires, one for each side. Base moulding plastic hooks can become brittle from spring tension.[3]

Guides:Psion Series 5 Hinge Wire Repair

USB adapter for the Honda serial portExperimental
ConnectivityDifficulty: mediumCase stays closedBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

The Psion syncs through a Honda serial plug. One project puts a CH340 USB-to-serial chip on that link so it can talk to a modern PC.[7]

Parts

  • CH340 USB-to-UART bridge Fits with conditions — Used in a cable project that converts a Honda serial cable to USB; the author says it works on the Series 5 and 5mx.[7]

Good to know

  • Psion machines, including the Series 5 and 5mx, use a Honda serial connector for PC sync.[7]
  • A project log entombs a small CH340 USB-to-UART board in the DB9 end of a cable to talk to a modern computer.[7]

Guides:No guide found yet.

New mainboard in the original caseExperimental
Shell reuseDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Hobby projects keep the original case and mechanics, and replace the electronics with a newly designed board. Goals include a better touch screen and a rechargeable battery.[5][6]

Good to know

  • One project aims to fit modern components into the Psion 5/5mx body, with a high-quality touch screen, a built-in rechargeable battery and full keyboard function like the original.[5]
  • Another write-up replaces all the electronics of the Psion 5 while keeping the mechanics; the main board outline is in KiCad, with a microcontroller to decode the keyboard.[6]

Guides:No guide found yet.

Sources (8)

SOURCES.TXT