★ 132 device pages approved★ 1511 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 132 device pages approved★ 1511 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000138devices tracked

Home › Devices › SanDisk › SanDisk Sansa Clip+

[ device photo ]CUSTOM FW!

SANDISK · MUSIC PLAYER · 2009

SanDisk Sansa Clip+

Also called: Sansa Clip · Sansa Clip+ · Clip Plus · Sansa Clip Zip · SDMX18

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 13 sources · 2 item(s) unverified

Tiny OLED clip player with built-in lithium battery, FM radio, mic, and (on Clip+) a microSDHC slot. Rockbox has a stable port for Clip, Clip+, and Clip Zip; common hardware work is battery replacement and headphone-jack repair.[1][12][11]

5MODS
3WORK
2EXPERIMENTAL
13SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Sansa ClipOriginal Clip (pre-Clip+)—Earlier Clip body, before the Clip+ redesign. Rockbox lists it with Clip+ and Clip Zip as a stable target. Battery-swap answers for this body are separate from Clip+.[12][5]
Sansa Clip+Clip+ 2 / 4 / 8 GB2009Square case redesign with a non-backlit navigation pad and a microSDHC slot. Common battery code on the pack is 323036P.[1][6]
Sansa Clip ZipClip Zip—Listed with Clip and Clip+ as a stable Rockbox target.[12]
Specs
Screen4-line OLED[1][11]
Storage (Clip+)2 GB / 4 GB / 8 GB internal variants; microSDHC expansion (iFixit cites up to 32 GB)[1][11]
BatteryBuilt-in rechargeable lithium-ion; Clip+ OEM pack often labeled 323036P (~30×36×3 mm)[1][6][2]
Ports3.5 mm headphone jack; USB 2.0 for transfer and charging (a forum user calls the port mini-USB)[1][11][10]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Rockbox custom firmwareWorks
SoftwareDifficulty: mediumCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Open-source firmware that dual-boots with SanDisk's. Adds codecs, themes, and (per Clip+ reports) longer runtime. Install with Rockbox Utility using an OEM firmware .bin to patch the bootloader.[12][13][1][8][7]

Good to know

  • Rockbox lists Clip, Clip+, and Clip Zip as stable targets with a released bootloader and Rockbox Utility support.[12]
  • Install route: Rockbox Utility patches the bootloader using an OEM firmware .bin, then loads rockbox.zip.[12]
  • iFixit describes the Clip+ Rockbox port as relatively mature and says it significantly improves battery life versus stock.[1]
  • Early 2010 forum reports called the port unstable and named a brick risk; dual boot to stock firmware was already present.[8]
  • Shared Rockbox notes call out OLED burn-in on Clip+ and the small stock battery as practical limits.[12]

⚠ Watch out

  • If Rockbox hangs (e.g. on the FM screen), hold power 10–15 seconds until it shuts off.[7]

Guides:No guide found yet.

Replace the lithium batteryWorks
BatteryDifficulty: hardOpens caseBasic solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Pry the case open, lift the cell off the memory chip, and fit a matching 3.7 V pack (Clip+ search code 323036P) or a carefully sized substitute. The OEM pack uses three wires; some successful swaps ignore the third sense wire.[2][6][5][4][9]

Special tools: plastic pry tool

Parts

  • 3.7 V cell matching 323036P (≈30×36×3 mm) Fits with conditions — Clip+ label code. Wires often need shortening so the case closes. Original Clip answers cite ~300 mAh 3.7 V packs (e.g. Shuffle donors); sizes differ by body.[6][2][5]

Good to know

  • The Clip+ is tiny and hard to open without damage; the OEM 30×36×3 mm cell is scarce.[2]
  • OEM Clip+ packs use three wires; one build that reused the small protection board gave no voltage, then a two-wire swap (ignoring the third) started the player.[2][9]
  • On the original Clip, the small board on the three battery wires must be reused when changing the cell.[5]

⚠ Watch out

  • The battery is glued to a memory chip—lift carefully. Minimize iron contact on the board (under about five seconds at a time on the original-Clip method).[4][5]

Guides:SOLVED: Where can I find a new battery? - Sansa Clip Plus - iFixitSOLVED: How to replace dead battery in Sansa Clip mp3 player? - Sandisk Sansa Clip - iFixit

External 14500 battery packExperimental
BatteryDifficulty: hardCase stays closedBasic solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Wire an external 14500 Li-ion cell in a holder to the player without changing the internal pack. One recent forum build claimed about 2.6× capacity versus stock.[10]

Good to know

  • A 2026 forum build used an external holder and a 14500 cell (~750 mAh) and reported roughly 2.6× capacity versus the stock cell.[10]

Guides:No guide found yet.

Reflow loose headphone jackWorks
RepairDifficulty: hardOpens caseBasic solderingReversible10 min
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Open the case, lift the battery, and reflow the three solder pads around the 3.5 mm jack. About ten minutes once the shell is open.[4]

Special tools: plastic pry tool, fine soldering iron

Good to know

  • iFixit rates the Clip+ loose-jack guide Difficult and about ten minutes; remove any microSD card first.[4]

⚠ Watch out

  • Pry at the upper-right corner with a plastic tool; the battery is glued down and must be lifted before jack work.[4]

Guides:Repairing Loose Headphone Jack - iFixit Repair Guide

Add a line-in jackExperimental
AudioDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Tap the FM radio ADC signals and epoxy a jack to the case base so the Clip+ can take line-level audio. The built-in mic can stay in place with this method.[3][11]

Good to know

  • Stock Clip+ has no line-in jack and only the built-in mic for recording.[3][11]
  • The published method taps FM-chip ADC lines and keeps the microphone intact.[3]

Guides:No guide found yet.

Buttons & modes

BUTTONS.TXT
WhatHow
Force power offHold the power button 10–15 seconds until the player shuts off (recovery used after Rockbox hangs).[7]

Sources (13)

SOURCES.TXT