★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000147devices tracked

Home › Devices › Dubreq › Stylophone

[ device photo ]NEW!

DUBREQ · INSTRUMENT · 1968

Stylophone

Also called: Dubreq Stylophone · Stylophone S-1 · Stylophone Beatbox

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 14 sources · 5 item(s) unverified

Pocket stylus synthesizer (original analogue through the 2007 S-1 reissue and 2009 Beatbox). Common mods are pitch/LDR circuit bends on original-style units and MIDI controller conversions on the glued reissue; Beatbox bends and modular CV builds appear mainly as showcases.[2][5][11][1]

4MODS
2WORK
2EXPERIMENTAL
14SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
OriginalStandard / Treble / Bass (1968–1975)1968Analogue resistor-ladder keyboard. Production of originals ended about 1975. MIDI conversion kit is not designed for these.[2][12]
S-12007 reissue2007Relaunched by Re:creation with Dubreq. Digital chip and 20-line keypad readable without cutting the original circuit; case is glued shut.[2][1][11]
Beatbox13-pad percussion (2009)2009Circular 13-pad stylus surface with drums/vocal/synth-bass sets, record/loop. Succeeded by the 2023 Stylophone Beat.[2][3][4]
Specs
Power (S-1 / Beatbox)3× AA (not included); S-1 needs no charging[1][3]
S-1 I/OBuilt-in speaker, 3.5 mm line in and line out, optional headphone jack; Power, Volume, Vibrato, 3-way octave[1]
Original circuitEach key feeds a VCO through a different-value resistor[2]

Mods (4)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Pitch range and light-controlled bendsWorks
AudioDifficulty: mediumOpens caseBasic solderingPermanent1-2 hr
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Add a 100k pot in series with the rear tuning pot for wider pitch, optionally an LDR/DPDT theremin-like light control, and an LDR from audio out to amp in for feedback overdrive.[5][6]

Parts

  • 100k potentiometer (series with tuning pot) Fits with conditions — The author says a log or larger pot would reach the lowest pitches better.[5]
  • LDR (light-dependent resistor) Fits — Between audio output and input is one of the easiest mods; changing output loading makes effects weirder.[5][6]

Good to know

  • mitxela raised pitch range with a 100k pot in series with the back tuning pot and kept original functions.[5]
  • A DPDT + LDR on the tuning path locks the top note for light-controlled pitch; another LDR into the amp path mixes self-oscillation/overdrive with the volume control as a mixer.[5]

Guides:Stylophone Circuit Bending

MIDI controller (reissue)Works
ConnectivityDifficulty: hardOpens caseBasic solderingPermanent2-6 hr
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Read the reissue keypad with shift registers or a resistor-ladder ADC and send MIDI, optionally with tilt pitch-bend. A Tindie conversion kit existed but is retired and not for 1970s analogue units.[11][12][13][14]

Special tools: USB TTL programmer (kit), Superglue (kit)

Parts

  • Sixty Four Pixels MIDI Stylophone kit Fits with conditions — Retired on Tindie. Not for original 1970s/80s analogue models. Fiddly build — read instructions first.[12] Buy: tindie.com

Good to know

  • Reissue units use a digital chip and 20 keypad lines readable via three 74HC165 shift registers while the Stylophone sound still works; a KXPS5 accelerometer provides pitch bend.[11]
  • Earlier method: solder to the keypad resistor ladder, read stylus voltage on an Arduino analog pin, send MIDI note on/off.[14]
  • sushyoshi/MIDI-Stylophone uses the stylus keys as a MIDI controller into a VS1053 with pots for pitch bend, octave, and tempo.[13]

⚠ Watch out

  • The reissue case is glued shut, and opening it without breaking the plastic is hard. Accelerometer enable must go high only after power-up.[11]

Guides:Stuff and Nonsense: January 2012sushyoshi/MIDI-Stylophone

Beatbox circuit bendsExperimental
AudioDifficulty: expertOpens caseBasic solderingPermanentunknown
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Seller builds add LDR warble on the pitch pot, record start/stop side buttons, pitch/LFO controls, and loop switches. [7][8]

Good to know

  • One modded Beatbox added an LDR plus flashing LED to the pitch pot (warble strongest on Bass #3) and a side momentary record start/stop button.[7] unverified
  • Another listing claimed pitch control, hi/low tone buttons, LFO with rate, 14 loop switches, and a random glitch button.[8] unverified

Guides:No guide found yet.

CV / gate modular bendsExperimental
ConnectivityDifficulty: expertOpens caseBasic solderingPermanentunknown
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Showcase units add extreme pitch, sustain switches, CV/gate inputs, filters, and amplified outs for Eurorack.[10][9]

Good to know

  • Bent Stylophones have been shown with CV input/gain, gate, two-way filter/VCF, sustain, and amplified mono out interacting with Eurorack.[10][9] unverified

Guides:No guide found yet.

Sources (14)

SOURCES.TXT