★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000147devices tracked

Home › Devices › Bandai › Tamagotchi

[ device photo ]NEW!

BANDAI · HANDHELD CONSOLE · 1996

Tamagotchi

Also called: Tama · Tamagotchi P1 · Tamagotchi Connection · Tamagotchi Paradise

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 17 sources · 2 item(s) unverified

Bandai virtual-pet line from the 1996 P1 through Connection and Paradise. Community work covers LR44 battery repair on the P1, OpenTama / MCUGotchi boards that emulate the P1, Paradise dock UART adapters, and Connection IR research.[12][2][3][7][15]

5MODS
3WORK
2EXPERIMENTAL
17SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Tamagotchi P1 / P2Original 1996 line1996First-generation egg-shaped pet. Takes two LR44 cells under a screw-down battery cover. Also called P1 or P2 by version.[12][10][11][9]
Tamagotchi Connection2004 IR / 2024 20th-anniversary re-release2004Infrared friend link. The 2024 US revival (version 3) keeps IR play and an antenna; other Connection versions use a different IR format.[15][16][17]
Tamagotchi ParadiseDock / connect series—Colour models such as Blue Water, Pink Land, and Purple Sky. Dock two units to connect. Bandai confirmed a display bug after age 256 with no planned replacements.[13][14]
Specs
P1 hardwareEpson E0C6S46 MCU, 32×16 LCD with 8 icons, three buttons, piezo speaker, two LR44 cells[1][5][10]
Paradise MCUSonix SNC73410 (32-bit)[8]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

OpenTama / MCUGotchi P1 emulator boardWorks
Shell reuseDifficulty: hardCase stays closedFine solderingReversibleseveral hours
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Build or flash an STM32 board that runs an emulated original P1. OpenTama is the open hardware reference with USB-C charging; MCUGotchi is the firmware.[1][2][3][4][5]

Special tools: GNU ARM toolchain, OpenOCD or dfu-util

Parts

  • OpenTama (STM32L072) board Fits with conditions — 128×64 UC1701x LCD or SSD1306 OLED, RGB LED, speaker, three buttons, USB-C. Battery and screen must be soldered by hand.[3][2]
  • Li-Po / Li-ion cell for OpenTama Fits with conditions — OpenTama design assumes a 1000 mAh 40×30×12 mm cell.[3][4]

Good to know

  • TamaLIB emulates the P1/P2 Epson E0C6S46. MCUGotchi runs it on STM32F0/L0 boards including OpenTama.[1][2][5]
  • Build with a GNU ARM toolchain, then flash with OpenOCD or dfu-util (OpenTama: hold BOOT0 and reset for DFU).[2][3]
  • You must supply a dump of your own original Tamagotchi. This page does not link to dumps.[2]

Guides:mcugotchi - Tamagotchi P1 emulator for microcontrollersopentama - open-source reference design for MCUGotchi

P1 battery replacementWorks
BatteryDifficulty: easyCase stays closedNo solderingReversible5-10 min

Swap the two LR44 cells under the screw-down cover. Use a JIS #0 driver; vintage screws strip easily.[10][11][9]

Special tools: JIS #0 screwdriver

Parts

  • LR44 / LR1154 / AG13 / A76 / 357 cells (pair) Fits with conditions — P1 takes two of these. Newer Tamagotchi models that use a CR-2032 are not this guide.[10][11]

Good to know

  • The P1 holds two LR44 cells under a cover with two screws.[10][11]
  • A JIS screwdriver (not Phillips), size 0, is recommended because vintage screws are soft.[10]

⚠ Watch out

  • Old cells can leak and corrode contacts; remove them as soon as the cover is open.[10]

Guides:How to replace my Tamagotchi's P1 battery without any risk?

P1 case open / screen and buttonsWorks
RepairDifficulty: mediumOpens caseNo solderingReversible30-60 min
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Open the four-screw case to reach the piezo, LCD spacers, and one-piece buttons. Useful for adjusting the LCD spacers or swapping button colour from a donor.[11]

Good to know

  • Four screws hold the case; the reset button can fall out when it opens.[11]
  • LCD contact is by spacers; pressure makes the screen work against the board.[11]
  • The three buttons are one piece and lift out; a colour change needs a donor unit.[11]

⚠ Watch out

  • Working inside can damage the toy. Avoid carpet static; use a strap if you have one.[11]

Guides:Tamagotchi Surgery!

Paradise dock UART adapterExperimental
ConnectivityDifficulty: hardCase stays closedBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

A CH340G USB-UART board with nickel-strip pogo contacts in a 3D-printed dock case talks to Paradise over its dock pins.[7][8]

Good to know

  • Builders wire three pins of a CH340G board to nickel strips that act as pogo contacts on the Paradise dock.[7][8]
  • Paradise runs a Sonix SNC73410. Browser tools have been used over this UART link for custom software.[8]

Guides:No guide found yet.

Connection IR link researchExperimental
ConnectivityDifficulty: hardCase stays closedBasic solderingReversible

Community reverse engineering of the Tamagotchi Connection infrared friend protocol (near-NEC style) with an RP2040 transceiver.[6][17][15]

Good to know

  • The Connection IR link behaves like IrDA; the studied protocol is described as nearly NEC.[6]
  • A research transceiver used an RP2040 with an IR LED and receiver.[6]
  • Work focused on the 2024 Connection version 3; other Connection versions use a different IR format.[17][15]

Guides:No guide found yet.

Sources (17)

SOURCES.TXT