Home › Devices › Bandai › Tamagotchi
BANDAI · HANDHELD CONSOLE · 1996
Tamagotchi
Also called: Tama · Tamagotchi P1 · Tamagotchi Connection · Tamagotchi Paradise
Bandai virtual-pet line from the 1996 P1 through Connection and Paradise. Community work covers LR44 battery repair on the P1, OpenTama / MCUGotchi boards that emulate the P1, Paradise dock UART adapters, and Connection IR research.[12][2][3][7][15]
Which one do I have?
| Model | Variant | Year | How to tell |
|---|---|---|---|
| Tamagotchi P1 / P2 | Original 1996 line | 1996 | First-generation egg-shaped pet. Takes two LR44 cells under a screw-down battery cover. Also called P1 or P2 by version.[12][10][11][9] |
| Tamagotchi Connection | 2004 IR / 2024 20th-anniversary re-release | 2004 | Infrared friend link. The 2024 US revival (version 3) keeps IR play and an antenna; other Connection versions use a different IR format.[15][16][17] |
| Tamagotchi Paradise | Dock / connect series | — | Colour models such as Blue Water, Pink Land, and Purple Sky. Dock two units to connect. Bandai confirmed a display bug after age 256 with no planned replacements.[13][14] |
Specs
Mods (5)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
OpenTama / MCUGotchi P1 emulator boardWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
Build or flash an STM32 board that runs an emulated original P1. OpenTama is the open hardware reference with USB-C charging; MCUGotchi is the firmware.[1][2][3][4][5]
Special tools: GNU ARM toolchain, OpenOCD or dfu-util
Parts
- OpenTama (STM32L072) board Fits with conditions — 128×64 UC1701x LCD or SSD1306 OLED, RGB LED, speaker, three buttons, USB-C. Battery and screen must be soldered by hand.[3][2]
- Li-Po / Li-ion cell for OpenTama Fits with conditions — OpenTama design assumes a 1000 mAh 40×30×12 mm cell.[3][4]
Good to know
- TamaLIB emulates the P1/P2 Epson E0C6S46. MCUGotchi runs it on STM32F0/L0 boards including OpenTama.[1][2][5]
- Build with a GNU ARM toolchain, then flash with OpenOCD or dfu-util (OpenTama: hold BOOT0 and reset for DFU).[2][3]
- You must supply a dump of your own original Tamagotchi. This page does not link to dumps.[2]
Guides:mcugotchi - Tamagotchi P1 emulator for microcontrollersopentama - open-source reference design for MCUGotchi
P1 battery replacementWorks
Swap the two LR44 cells under the screw-down cover. Use a JIS #0 driver; vintage screws strip easily.[10][11][9]
Special tools: JIS #0 screwdriver
Parts
- LR44 / LR1154 / AG13 / A76 / 357 cells (pair) Fits with conditions — P1 takes two of these. Newer Tamagotchi models that use a CR-2032 are not this guide.[10][11]
Good to know
- The P1 holds two LR44 cells under a cover with two screws.[10][11]
- A JIS screwdriver (not Phillips), size 0, is recommended because vintage screws are soft.[10]
⚠ Watch out
- Old cells can leak and corrode contacts; remove them as soon as the cover is open.[10]
Guides:How to replace my Tamagotchi's P1 battery without any risk?
P1 case open / screen and buttonsWorks
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Open the four-screw case to reach the piezo, LCD spacers, and one-piece buttons. Useful for adjusting the LCD spacers or swapping button colour from a donor.[11]
Good to know
- Four screws hold the case; the reset button can fall out when it opens.[11]
- LCD contact is by spacers; pressure makes the screen work against the board.[11]
- The three buttons are one piece and lift out; a colour change needs a donor unit.[11]
⚠ Watch out
- Working inside can damage the toy. Avoid carpet static; use a strap if you have one.[11]
Guides:Tamagotchi Surgery!
Paradise dock UART adapterExperimental
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
A CH340G USB-UART board with nickel-strip pogo contacts in a 3D-printed dock case talks to Paradise over its dock pins.[7][8]
Good to know
- Builders wire three pins of a CH340G board to nickel strips that act as pogo contacts on the Paradise dock.[7][8]
- Paradise runs a Sonix SNC73410. Browser tools have been used over this UART link for custom software.[8]
Guides:No guide found yet.
Connection IR link researchExperimental
Community reverse engineering of the Tamagotchi Connection infrared friend protocol (near-NEC style) with an RP2040 transceiver.[6][17][15]
Good to know
- The Connection IR link behaves like IrDA; the studied protocol is described as nearly NEC.[6]
- A research transceiver used an RP2040 with an IR LED and receiver.[6]
- Work focused on the 2024 Connection version 3; other Connection versions use a different IR format.[17][15]
Guides:No guide found yet.
Sources (17)
- official tamalib - first-gen Tamagotchi emulation library · 2026-11-16
- official mcugotchi - Tamagotchi P1 emulator for microcontrollers · 2026-11-16
- official opentama - open-source reference design for MCUGotchi · 2026-11-16
- news Classic Tamagotchi Is Reincarnated In Modern Hardware · 2026-11-16
- news Tamagotchis Everywhere · 2026-11-16
- news Reverse-Engineering The Tamagotchi IR Connection · 2026-11-16
- news Hacking The Modern Tamagotchi With UART · 2026-11-16
- news Three Nickel Strips and a USB Adapter Get This Tamagotchi Running Custom Software · 2026-11-16
- docs Tamagotchi Repair Help · 2026-11-16
- forum How to replace my Tamagotchi's P1 battery without any risk? · 2026-11-16
- blog Tamagotchi Surgery! · 2026-11-16
- blog Another Icon's Teardown: Tamagotchi Original · 2026-11-16
- official Tamagotchi Paradise · 2026-11-16
- official Notice regarding Tamagotchi Paradise · 2026-11-16
- official Tamagotchi Connection 20th Anniversary! · 2026-11-16
- blog Tamagotchi Connection: Facts and Tips · 2026-11-16
- blog Making Friends (out of thin air) · 2026-11-16