Home › Devices › Tecsun › Tecsun PL-660
TECSUN · RADIO · 2010
Tecsun PL-660
Also called: PL-660 · PL660
Portable HF/VHF receiver with four AA cells, a ferrite bar, and an external FM/SW antenna jack. Owners disable soft mute and dynamic squelch, couple external antennas to LW/MW, and use hidden frequency calibration.[7][5][1][4]
Which one do I have?
| Model | Variant | Year | How to tell |
|---|---|---|---|
| PL-660 | Worldwide portable | 2010 | Manufactured from 2010. Early firmware (e.g. 6601) lacks memory sort and calibration features that later units add. Related to the PL-680 but not identical — one comparison calls the PL-660 more sensitive and the PL-680 better at high-volume audio.[7][6][9] |
Specs
| Coverage | 0.1–30 MHz HF plus FM (87–108 MHz general / 76–108 MHz Japan) and 118–137 MHz air band[7] |
| Power | Four AA cells, or 6 V DC on a 3.5 mm jack[7][8][6] |
| Antennas | Built-in telescopic whip and ferrite bar; external FM/SW antenna jack (no stock LW/MW external switch)[7][8][5] |
| Audio out | No line-out jack; headphones required to monitor while recording[10] |
Mods (6)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Disable soft muteExperimental
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Two solder joints and a scratched board path near the tone switch stop soft mute. Documented on the PL-680; the author says the same work applies to the PL-660 but does not own one.[1][6]
Good to know
- Soft mute is disabled with two solder joints and by scratching a path on the print near the switch.[1]
- The author notes the same work applies to a PL-660 but tested it only on a PL-680; he does not own a PL-660.[1]
Guides:Tecsun PL-680: Rolf touts enhanced performance using PL-660 mod
External antenna for LW/MWExperimental
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Wind a transfer coil on the ferrite bar, or use the unused ring terminal of the stereo external-antenna jack to ground. Stock radio has no LW/MW external-antenna switch.[5]
Good to know
- One owner wound a 5-turn transfer coil around the ferrite bar and brought it out through the wrist-strap hole to a phone jack.[5]
- Another method (Geir Laastad) uses the unused centre/ring terminal of the stereo external antenna jack to radio ground. Tecsun used the same jack approach on the PL-600, PL-660, and PL-680.[5]
- The PL-660 has no means to switch on an external LW/MW antenna from the stock controls.[5]
Disable dynamic squelchExperimental
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Ground one lead of a transistor on the PCB after unsoldering a large shield. Removes weak-signal blocking and on-off chatter.[5]
Good to know
- Dynamic squelch can be permanently turned off by grounding one transistor lead after removing a large metal circuit shield.[5]
Guides:No guide found yet.
Hidden FM / band calibrationExperimental
Software calibration of FM, and of AM and SW bandwidths. No case opening. The FM steps are untested by the person who posted them.[4][3][6]
Good to know
- Quoted FM steps: with the radio on FM, hold SYNC about three seconds, tune until the station is clearer, press 1 to confirm. Keep the battery in the whole time.[4]
- A separate video guide covers calibrating AM, FM, and SW wide/narrow independently and resetting to factory default. Owners report wide SW can read up to 5 kHz low.[3]
- Later firmware units add a tuning calibration feature; early 6601 units may lack it.[6]
Guides:Tecsun PL-660 Hidden Feature: FM CalibrationVideo: How to calibrate the Tecsun PL-660 frequency offset
Larger tuning knobExperimental
Swap the stock small tuning knob for a larger one from another control. Fit can be awkward because the knob must clear the tuner cam.[2][5]
Good to know
- A larger knob makes the tuning control easier to turn than the stock small knob.[2]
- A foam packing spacer slipped over the fine-tuning knob can ease the detent and add gear reduction.[5]
Guides:No guide found yet.
Telescopic antenna or kickstand replacementWorks
Sources (10)
- blog Tecsun PL-680: Rolf touts enhanced performance using PL-660 mod · 2026-11-16
- blog Simple hack: Changing the tuning knob on the PL-660 · 2026-11-16
- blog Video: How to calibrate the Tecsun PL-660 frequency offset · 2026-11-16
- blog Tecsun PL-660 Hidden Feature: FM Calibration · 2026-11-16
- blog Bob’s Radio Corner: The Last Radio I Really Needed · 2026-11-16
- blog Re-Viewing Radios – Tecsun PL-660 · 2026-11-16
- docs RigPix Database - Tecsun PL-660 · 2026-11-16
- blog LEAP#742 Tecsun PL-660 notes · 2026-11-16
- blog Tecsun PL-660 tag archive (SWLing Post) · 2026-11-16
- blog Monitoring while recording on the Tecsun PL-660 · 2026-11-16