★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000147devices tracked

Home › Devices › Tecsun › Tecsun PL-660

[ device photo ]NEW!

TECSUN · RADIO · 2010

Tecsun PL-660

Also called: PL-660 · PL660

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 10 sources · 6 item(s) unverified

Portable HF/VHF receiver with four AA cells, a ferrite bar, and an external FM/SW antenna jack. Owners disable soft mute and dynamic squelch, couple external antennas to LW/MW, and use hidden frequency calibration.[7][5][1][4]

6MODS
1WORK
5EXPERIMENTAL
10SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
PL-660Worldwide portable2010Manufactured from 2010. Early firmware (e.g. 6601) lacks memory sort and calibration features that later units add. Related to the PL-680 but not identical — one comparison calls the PL-660 more sensitive and the PL-680 better at high-volume audio.[7][6][9]
Specs
Coverage0.1–30 MHz HF plus FM (87–108 MHz general / 76–108 MHz Japan) and 118–137 MHz air band[7]
PowerFour AA cells, or 6 V DC on a 3.5 mm jack[7][8][6]
AntennasBuilt-in telescopic whip and ferrite bar; external FM/SW antenna jack (no stock LW/MW external switch)[7][8][5]
Audio outNo line-out jack; headphones required to monitor while recording[10]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Disable soft muteExperimental
AudioDifficulty: hardOpens caseFine solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Two solder joints and a scratched board path near the tone switch stop soft mute. Documented on the PL-680; the author says the same work applies to the PL-660 but does not own one.[1][6]

Good to know

  • Soft mute is disabled with two solder joints and by scratching a path on the print near the switch.[1]
  • The author notes the same work applies to a PL-660 but tested it only on a PL-680; he does not own a PL-660.[1]

Guides:Tecsun PL-680: Rolf touts enhanced performance using PL-660 mod

External antenna for LW/MWExperimental
ConnectivityDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Wind a transfer coil on the ferrite bar, or use the unused ring terminal of the stereo external-antenna jack to ground. Stock radio has no LW/MW external-antenna switch.[5]

Good to know

  • One owner wound a 5-turn transfer coil around the ferrite bar and brought it out through the wrist-strap hole to a phone jack.[5]
  • Another method (Geir Laastad) uses the unused centre/ring terminal of the stereo external antenna jack to radio ground. Tecsun used the same jack approach on the PL-600, PL-660, and PL-680.[5]
  • The PL-660 has no means to switch on an external LW/MW antenna from the stock controls.[5]

Guides:Bob’s Radio Corner: The Last Radio I Really Needed

Disable dynamic squelchExperimental
AudioDifficulty: hardOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Ground one lead of a transistor on the PCB after unsoldering a large shield. Removes weak-signal blocking and on-off chatter.[5]

Good to know

  • Dynamic squelch can be permanently turned off by grounding one transistor lead after removing a large metal circuit shield.[5]

Guides:No guide found yet.

Hidden FM / band calibrationExperimental
SoftwareDifficulty: noneCase stays closedNo solderingReversible

Software calibration of FM, and of AM and SW bandwidths. No case opening. The FM steps are untested by the person who posted them.[4][3][6]

Good to know

  • Quoted FM steps: with the radio on FM, hold SYNC about three seconds, tune until the station is clearer, press 1 to confirm. Keep the battery in the whole time.[4]
  • A separate video guide covers calibrating AM, FM, and SW wide/narrow independently and resetting to factory default. Owners report wide SW can read up to 5 kHz low.[3]
  • Later firmware units add a tuning calibration feature; early 6601 units may lack it.[6]

Guides:Tecsun PL-660 Hidden Feature: FM CalibrationVideo: How to calibrate the Tecsun PL-660 frequency offset

Larger tuning knobExperimental
Buttons & inputDifficulty: easyCase stays closedNo solderingReversible

Swap the stock small tuning knob for a larger one from another control. Fit can be awkward because the knob must clear the tuner cam.[2][5]

Good to know

  • A larger knob makes the tuning control easier to turn than the stock small knob.[2]
  • A foam packing spacer slipped over the fine-tuning knob can ease the detent and add gear reduction.[5]

Guides:No guide found yet.

Telescopic antenna or kickstand replacementWorks
RepairDifficulty: easyCase stays closedNo solderingReversible

Swap a broken telescopic whip or kickstand with aftermarket parts (e.g. XHDATA antenna, Anon-co kickstand).[6]

Good to know

  • One owner replaced a failed telescopic antenna with an XHDATA part and a broken kickstand from Anon-co.[6]

Guides:No guide found yet.

Sources (10)

SOURCES.TXT