★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000080devices tracked

Home › Devices › Bandai › WonderSwan Color

[ device photo ]NEW!

BANDAI · HANDHELD CONSOLE · 2000

WonderSwan Color

Also called: WSC · Bandai WonderSwan Color

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 11 sources · 4 item(s) unverified

Bandai's color WonderSwan from December 2000 (Japan). Reflective color screen with no backlight, one AA battery, and play of original WonderSwan cartridges. Documented changes add a USB-C battery door, a flashcart for homebrew, capacitor kits, EXT-port USB, a DIY backlight, a 1.5 V LiPo regulator, and an open consolizer.[1][2][3]

8MODS
1WORK
7EXPERIMENTAL
11SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
WonderSwan ColorColor handheld2000Japan release December 9, 2000. Reflective color screen with no backlight. One AA battery. Plays original WonderSwan cartridges. Not the monochrome WonderSwan or SwanCrystal.[1]
Specs
Screen2.8-inch FSTN reflective LCD, 224×144, 241 of 4096 colors, no backlight[1]
CPUSPGY-1002, 3.072 MHz 16-bit NEC V30MZ clone[1]
Memory64 kB shared VRAM/WRAM[1]
Power1× AA; about 20 hours claimed with the stock unlit screen[1]

Mods (8)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

USB-C rechargeable packExperimental
BatteryDifficulty: easyCase stays closedNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

A lithium pack with USB-C charging replaces the AA door. Curvature is made for WonderSwan Color (also fits SwanCrystal). Aimed at Color units with an IPS screen.[2]

Parts

  • RetroOnyx WonderSwan battery pack Fits — Snug fit on WonderSwan Color; also fits SwanCrystal.[2] Buy: retroonyx.com

Good to know

  • Assembled pack for WonderSwan Color with USB-C charging, charge-while-playing, a 2300 mAh lithium cell, and over/under-voltage plus short-circuit protection.[2]
  • Maker lists about 11 hours with an IPS kit at minimum brightness and about 45 days standby.[2]
  • Curvature is designed for Color; SwanCrystal also fits. Black-and-white WonderSwan units work with a curvature mismatch.[2]

Guides:No guide found yet.

WS Flash MastaWorks
StorageDifficulty: easyCase stays closedNo solderingReversible

A programmable cartridge with micro-USB. It runs homebrew and your own cartridge backups on WonderSwan, WonderSwan Color, and SwanCrystal.[3]

Parts

  • WS Flash Masta USB Fits — Upload files over built-in micro-USB. Multiple slots share one SRAM save area.[3]

Good to know

  • The WS Flash Masta USB uploads files from a computer to the cartridge over built-in micro-USB for play on WonderSwan, WonderSwan Color, or SwanCrystal.[3]
  • The cartridge has multiple slots, but the SRAM save area is shared across slots.[3]

Guides:No guide found yet.

Backlit IPS screenExperimental
ScreenDifficulty: mediumOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace the reflective color panel with a backlit screen. RetroRGB covers a kit that needs inner plastic cut.[8][2]

Good to know

  • RetroRGB covers a backlit replacement screen the same size as the original WonderSwan panel.[8]
  • Install needs cutting some inner plastic so the panel fits.[8]
  • RetroOnyx designed its Color battery pack for users who upgraded to an IPS screen kit.[2]
  • The stock WonderSwan screen runs at 75 Hz; RetroRGB notes games that run near 60 Hz can sit too low on some replacement panels.[8] unverified

Guides:Wonderswan Backlight Mod Installation and Review – RetroRGB

DIY LED backlightExperimental
ScreenDifficulty: hardOpens caseBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

One blog builds an LED backlight from a DS Lite panel for a Wonder Swan. The write-up is titled for the monochrome unit and its stock runtime does not match the Color's 20-hour rating.[7][1]

Parts

  • DS Lite display LED and diffusion layers Fits with conditions — Salvaged from a faulty DS Lite screen; trimmed to the Wonder Swan panel. Write-up is for the monochrome shell.[7]

Good to know

  • The build peels the reflective layer from the Wonder Swan LCD and adds LED and diffusion layers from a DS Lite display.[7]
  • LEDs are powered from a stable 15 V point on the power regulator, with a 2.2 kΩ series resistor on ground to hold current near 55–60 mA.[7] unverified

⚠ Watch out

  • Current and runtime figures come from one blog. The title says Wonder Swan, and its ~40 hour stock figure does not match the WonderSwan Color's ~20 hour rating.[7][1] unverified

Guides:Custom backlight for a Wonder Swan

Capacitor replacementExperimental
RepairDifficulty: expertOpens caseFine solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Surface-mount cap kits for WonderSwan Color (and related Swan models). Flash Masta calls the work expert-level.[5][6][4]

Parts

  • Console5 WonderSwan Color SMD cap kit Fits — All parts to replace SMD electrolytics in the WonderSwan Color.[5] Buy: console5.com
  • Flash Masta WonderSwan cap kit Fits — Surface-mount caps for WS, WSC, and SwanCrystal. On Color, new C14 is slightly larger and close to the cart socket.[4] Buy: flashmasta.com

Good to know

  • Console5 sells an SMD electrolytic kit specifically for the WonderSwan Color motherboard.[5]
  • Console5 TechWiki lists Color values including C14 2.2 µF 35 V, C16 330 µF 4 V, and C19 220 µF 4 V.[6]
  • Flash Masta sells a surface-mount kit for Black & White, Color, and SwanCrystal and calls it expert-level soldering.[4]

Guides:No guide found yet.

EXT-to-USB development adapterExperimental
ConnectivityDifficulty: mediumCase stays closedBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

ws-extfriend is an RP2040-based USB adapter on the WonderSwan EXT port for serial and digital audio capture during homebrew work.[9]

Good to know

  • ExtFriend provides a USB serial port at WonderSwan baud rates and a USB audio device for digital stereo capture from the EXT port.[9]
  • Hardware build uses a Raspberry Pi Pico wired to EXT pins; digital audio needs four extra Pico pins.[9]

Guides:asiekierka/ws-extfriend

1.5 V LiPo regulator boardExperimental
BatteryDifficulty: hardOpens caseFine solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

A tiny open-source 1.5 V LDO board lets you power the console from a LiPo pack instead of a single AA.[10]

Parts

  • jit06 wonderswanreg 1.5 V LDO Fits — About 1×1 cm XC6210 board. Input 1.5–6 V; enable must be bridged to input. Gerbers and BOM are in the repo.[10]

Good to know

  • Open-source XC6210-based 1.5 V regulator that fits inside a WonderSwan and allows LiPo power.[10]

Guides:jit06/wonderswanreg: 1.5V wonderswan regulator

Digital video consolizerExperimental
ConnectivityDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

swancolorHD is an open-source WonderSwan Color consolizer on a Tang Nano 9k FPGA. The maker calls it somewhat usable, and it needs an external video core.[11]

Parts

  • swancolorHD consolizer PCB Fits — Uses a Tang Nano 9k, Arduino Nano, 24-pin FFC to the Color display connector, and a SNES controller. Project calls itself somewhat usable.[11]

Good to know

  • Open-source consolizer for WonderSwan Color based on a Tang Nano 9k FPGA board.[11]
  • Display connects with a 24-pin 0.5 mm same-side FFC; battery + maps to 1.5 V and battery − to GND on the consolizer PCB.[11]
  • Maker says the project is in a somewhat usable stage and needs an external video core.[11]

Guides:zwenergy/swancolorHD: WonderSwan Color consolizer

Buttons & modes

BUTTONS.TXT
WhatHow
Personal data screenHold Start and power at the same time.[1]

Sources (11)

SOURCES.TXT