★ 155 device pages approved★ 1835 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 155 device pages approved★ 1835 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000161devices tracked

Home › Devices › Yaesu › Yaesu FT-817

[ device photo ]NEW!

YAESU · RADIO · 2001

Yaesu FT-817

Also called: FT-817 · FT-817ND · FT817

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 13 sources · 3 item(s) unverified

All-mode QRP transceiver with fragile PA FETs and a known-weak DC socket. Documented work covers NiMH pack charging (green wire), soft-calibration / hidden menu, speaker swap, DC-jack workarounds, and out-of-band TX expansion (legal limits apply).[1][2][6][9]

6MODS
4WORK
2EXPERIMENTAL
13SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
FT-817Original2001Original portable all-mode QRP. Front BNC and rear UHF antenna connectors with per-band relay selection.[1][4]
FT-817NDUpdated pack / 60 m (USA)—Added 60 m coverage on the USA model, FNB-85 pack, and NC-72B charger.[1]
Specs
MakerBuilt by Vertex Standard in Japan; sold as Yaesu[1]
Memories202 memories (1–200 plus M-PL and M-PU)[5]
ControlSerial CAT port; microprocessor-controlled. Data modes often use the 6-pin mini-DIN data port[1][13]
PA / battery care2SK2975 final FETs are sensitive to high SWR and overvoltage. Remove the internal battery for long storage to avoid leakage damage[1]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Enable NiCd / NiMH pack chargingWorks
ChargingDifficulty: mediumOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Cut or disconnect the green wire in the alkaline pack so the radio will charge NiCd or NiMH cells. Add fuses; never charge alkalines afterward.[6][2]

Good to know

  • A circuit inhibits charging when alkaline cells are used. Disconnecting or snipping the green wire and insulating the loose end enables charging.[2][6]
  • Shorted NiCd/NiMH packs can deliver over 20 A. Fuse advice ranges from a 4 A fuse in the negative lead to 2–3 A Pico fuses in the positive leads.[2][6]

⚠ Watch out

  • After this change you can also charge alkaline cells, which is dangerous. KA7OEI cautions against the mod.[6][2]

Guides:YAESU FT-817 Mods!The KA7OEI FT-817 pages - Modifications

Hidden soft-calibration menuWorks
SoftwareDifficulty: hardCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Hold A, B, and C while powering on. Save with F. Includes AM-CAR (menu 69) for AM carrier level. Factory/test settings — easy to brick calibration.[7][3][6][5]

Good to know

  • Enter by holding A, B, and C while switching on. Press F to save parameters to EEPROM.[7][3][6]
  • Menu 69 (AM-CAR) sets AM carrier level, typically about 6 dB below peak. It does not raise peak AM output.[3]
  • FT-817 Commander can save and restore calibration values.[3]

⚠ Watch out

  • Do not change these values without test equipment. Wrong edits can wipe EEPROM calibration and memories.[3][7][5]

Guides:Hidden menu in Amateur RadioThe KA7OEI FT-817 pages - Soft Calibration Menu

Transmit range expansionExperimental
OtherDifficulty: hardOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Can brick A mistake can leave the device unable to start.

Internal jumper changes extend TX outside stock amateur allocations (e.g. MARS/CAP). Sources disagree on which jumpers to bridge. Transmit only where your licence allows.[6][8][2]

Good to know

  • One 2001 write-up describes a MARS/CAP-style expand that opens transmit coverage; another published scheme bridges different jumpers and was not cross-tested.[6]
  • A later build report bridges the first four jumper pads and opens the fifth, claiming HF/VHF/UHF TX expansion tested at home.[8]
  • KA7OEI: no known mods enable TX in 76–108 or 108–137 MHz; aero-band TX is illegal except in an emergency and the radio lacks proper filtering. CB, business, GMRS, and FRS use are called illegal for this radio.[2]

⚠ Watch out

  • You must check the rules for any new frequency before transmitting. Jumper procedures conflict across sources.[2][6][8]

Guides:YAESU FT-817 Mods!FT-817 TX extension

DC socket repair / PowerPole workaroundWorks
RepairDifficulty: hardOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

The rear DC input socket fails often. Options: remove the socket and hard-wire your own connector, or use a PowerPole adapter. Reversed polarity can burn ground traces and fuses.[9][10][11]

Parts

  • FT-817/818 PowerPole adapter Fits — Adapter that takes strain off the rear DC connector, which often fails; it does not repair a socket that has already failed.[11] Buy: sotabeams.co.uk

Good to know

  • The DC socket is widely called prone to failure. One fix removes the socket, exits two wires, and fits a chosen connector.[9][11]
  • Reversed power leads have burnt DC-input ground connections and a common-mode choke; some ND units use a ~2.3 A SMD PA-feed fuse.[10]

Guides:Stupid DC Socket design on Yaesu FT-817 FT-818Yaesu FT-817nd Repair

Drop-in speaker replacementWorks
AudioDifficulty: easyOpens caseNo solderingReversible

Swap the stock ~1.5 W speaker for a same-size wet-resistant ~2 W unit. Lift the cover carefully — the cable is short.[12]

Good to know

  • One builder used a larger water-resistant same-size speaker rated 2 W versus the stock 1.5 W and reported louder, clearer audio.[12]

Guides:Yaesu FT-817 speaker replacement

Noise blanker AGC resistorExperimental
AudioDifficulty: expertOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Can brick A mistake can leave the device unable to start.

Add a resistor (R1345 in KA7OEI's report) to slightly decrease AGC action in the noise blanker. Needs a service manual and SMD skill.[2]

Good to know

  • KA7OEI added R1345 to slightly decrease AGC action in the noise blanker. Not practical without a service manual.[2]

Guides:No guide found yet.

Buttons & modes

BUTTONS.TXT
WhatHow
Hidden calibration menuHold A, B, and C while powering on. Press F to save.[7][3]

Sources (13)

SOURCES.TXT