★ 177 device pages approved★ 2146 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 177 device pages approved★ 2146 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000183devices tracked

Home › Devices › Microsoft › Microsoft Zune 80

[ device photo ]NEW!

MICROSOFT · MUSIC PLAYER · 2007

Microsoft Zune 80

Also called: Zune 80 · Zune 80GB · Zune 120 · second-generation Zune

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 14 sources

Second-generation hard-drive Zune with a larger screen and touch pad. Common repairs are a soldered battery swap, 1.8-inch ZIF drive replacement (including period SSD builds), screen, and case opening. Rockbox does not support it. After a drive swap you must host your own firmware update server because Microsoft ended Zune services.[1][4][3][10][14]

6MODS
5WORK
0EXPERIMENTAL
14SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Zune 8080 GB second generation2007Slimmer second-generation body than the first-gen 30 GB Zune, with a bigger screen and a touch-sensitive directional pad.[2][1]
Zune 120120 GB second generation2008Same generation as the Zune 80 with a larger drive. A comment on the iFixit battery guide says the cap under the top screws is one complete unit on the 120.[1][4]
Specs
BatteryNon-removable Li-ion polymer, 850 mAh, soldered with four wires[1]
Storage1.8-inch PATA on a ZIF connector; Windows CE limit about 120 GB (including 128 GB SSDs)[1]
Firmware3.30 listed for Zune 80/120[1]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Hard drive replacementWorks
StorageDifficulty: mediumOpens caseNo solderingReversible15-20 min
  • ⚠ Data loss Can erase what is on the device. Back up first.

Open the case, unlatch the fragile ZIF cable, and swap the 1.8-inch PATA drive. After the swap, host your own firmware update server so Zune software can load firmware onto the new drive.[3][5][7][1]

Special tools: Torx screwdriver (T3 or T4 — guides conflict)

Good to know

  • iFixit hard-drive guide: remove the cap and two screws under it, back casing, silver tape, then the ZIF cable latch and drive. Rated Moderate, 15–20 minutes.[3]
  • The ZIF cable is very fragile; bend it as little as possible and check it before fitting a new drive.[3]
  • Compatibility is limited to 1.8-inch PATA ZIF drives. Windows CE appears to cap usable size around 120 GB.[1]
  • After a drive swap, host your own firmware update server because Microsoft ended Zune services.[1]
  • Screw type under the cap conflicts across iFixit pages: hard-drive guide says T3; teardown says T4.[3][7]

⚠ Watch out

  • Confirm Torx size on your unit before forcing screws. Do not kink the ZIF cable.[3][7]

Guides:Microsoft Zune 80 Hard Drive Replacement - iFixitMicrosoft Zune 80 Case Replacement - iFixit

1.8-inch ZIF SSD upgradeWorks
StorageDifficulty: mediumOpens caseNo solderingReversible
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace the spinning drive with a 1.8-inch ZIF SSD. Period builds put 32 GB SSDs in second-gen Zunes; stay within the ~120 GB Windows CE limit.[10][11][12][3][1][13]

Parts

  • 1.8-inch 40-pin ZIF SSD (e.g. Yansen 128 GB form-factor listing) Fits with conditions — Form factor and ZIF 40-pin interface only. Usable capacity may still be capped near 120 GB. Buyer claims of Zune fit are unverified.[13][1] Buy: memoryc.com

Good to know

  • A 2009 build replaced a failed second-gen Zune drive with a 32 GB SSD after error code 5. The builder said it used the slimmer second-generation model; TechCrunch and Gizmodo name the Zune 80.[10][11][12]
  • The SSD fitted with a little case modification and looked stock afterward.[10]
  • The Windows CE limit appears to be about 120 GB, including 128 GB SSDs.[1]

Guides:Microsoft Zune 80 Hard Drive Replacement - iFixit

Replacement batteryWorks
BatteryDifficulty: hardOpens caseFine solderingReversible30-50 min
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Open the case and desolder the four battery leads from the board. Wrong wiring can harm the device. A cell left unused for years may need replacing.[4][1][9][8]

Special tools: soldering iron, non-metal spudger, Torx screwdriver

Parts

  • Zune battery (forum search tip X814399-001) Fits with conditions — Part number suggested in one iFixit Answers post; not confirmed elsewhere in the kb.[9]

Good to know

  • iFixit battery guide requires soldering and rates the job Difficult, 30–50 minutes. Desolder the battery connections from the motherboard.[4]
  • The pack is soldered with four wires; incorrect wiring will likely harm the device.[1]
  • A battery left unused for years can be depleted past recovery and need replacement.[9]

⚠ Watch out

  • This is a soldered lithium pack. Wire it exactly as before: incorrect wiring will likely harm the device. Recycle the old cell properly.[4][1]

Guides:Microsoft Zune 80 Battery Replacement - iFixit

LCD screen replacementWorks
ScreenDifficulty: hardOpens caseFine solderingReversible15 min (guide claim; battery desolder adds time)
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Remove the case, drive, battery, and board, then replace the LCD. The iFixit path also desolders the battery, so plan for soldering.[6][4]

Good to know

  • iFixit screen guide replaces the Zune 80 LCD after opening the case and removing tape, drive, battery, and board. Rated Moderate, about 15 minutes.[6]
  • Step 12 uses a soldering iron to desolder the battery, so the screen job inherits the battery soldering step.[6]

Guides:Microsoft Zune 80 Screen Replacement - iFixit

Open the aluminum back caseWorks
CaseDifficulty: mediumOpens caseNo solderingReversible10 min

Release five clips per side and two on the bottom to remove the back casing and reach the internals. Watch for cables at the edge.[5]

Good to know

  • iFixit case guide: five clips on each side and two on the bottom. Do not press tools too far — exposed cables sit at the edge.[5]

Guides:Microsoft Zune 80 Case Replacement - iFixit

Rockbox custom firmwareNot possible
SoftwareDifficulty: noneCase stays closedNo solderingReversible

Rockbox does not offer a usable Zune 80 port. The model is absent from the stable-targets table.[14]

Good to know

  • Zune 80 is not in the stable-targets table and appears only under under-development Microsoft Zune text.[14]

Sources (14)

SOURCES.TXT