Home › Devices › Canon › Canon EOS 1100D
CANON · CAMERA · 2011
Canon EOS 1100D
Also called: EOS 1100D · Rebel T3 · Kiss X50 · EOS Rebel T3
Canon entry-level APS-C Rebel from 2011, also sold as the Rebel T3 and Kiss X50. Magic Lantern has a 1100D.105 port in the main tree. Stock video is 720p; Canon says an external microphone cannot be used.[1][10][4][11][2]
Which one do I have?
Specs
Mods (4)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Magic LanternWorks
- ⚠ Can brick A mistake can leave the device unable to start.
- ⚠ Data loss Can erase what is on the device. Back up first.
Free GPL add-on that runs from the SD card next to Canon firmware. The main tree has a 1100D.105 platform build. Wikipedia lists the 1100D among supported cameras.[11][4][13][14][15][12][6][3][16]
Parts
- SD or SDHC card, 32 GB or smaller Fits — Used for a first Magic Lantern install. The camera low-level formats it.[13]
Good to know
- Magic Lantern runs from the card as an add-on over standard Canon firmware. It does not replace firmware in ROM.[14][12]
- The bootloader uses a bootdisk flag and loads autoexec.bin from the card.[13]
- Wikipedia lists community ports for the 1100D among Magic Lantern supported cameras.[11]
- The Magic Lantern source tree includes a platform folder named 1100D.105.[4]
- Project features include audio controls, zebras, focus peaking, bitrate control, HDR video, and an intervalometer.[15]
- First install: use a simple SD or SDHC card of 32 GB or smaller and a fully charged original battery. The card is low-level formatted; copy the files and run Canon firmware update.[13]
- Hold SET at startup to bypass Magic Lantern for one session. Full uninstall runs Firmware Upgrade in-camera to clear the boot flag.[14]
- For raw video, EOSHD puts the 1100D in the slowest class (older about 20 MB/s SD controller) and does not recommend it for RAW video.[6]
⚠ Watch out
- The platform folder name is 1100D.105. Canon newest official firmware for this body is 1.0.6. Match the build to the firmware on the camera.[4][3]
- The project warns that third-party software can damage or destroy the camera. Magic Lantern writes settings to NVRAM that Canon firmware does not always validate.[13][14]
- After you open the card door, wait for the card LED to finish before removing the card. A bootable card without autoexec.bin can leave the camera unable to boot until you pull the battery.[13]
- Canon does not cover repairs caused by third-party firmware.[16]
Guides:Magic Lantern INSTALL.txt
Replace the LP-E10 batteryWorks
- ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
The camera takes a Canon LP-E10 pack (7.4 V, 860 mAh). Charge with the LC-E10 or LC-E10E. The card slot sits beside the battery.[1][7]
Parts
- Canon LP-E10 Fits — Canon lists the LP-E10 as the rechargeable lithium-ion pack for this body.[1]
Good to know
- Canon rates the pack at 860 mAh and 7.4 V DC. The LC-E10 / LC-E10E charger takes about two hours at 23 C.[1]
- CIPA battery life is about 700 shots with the viewfinder and about 220 with Live View.[1]
- The card slot sits alongside the battery compartment.[7]
Guides:No guide found yet.
Front cover replacementWorks
- ⚠ Stored charge Capacitors keep a dangerous charge after the device is off.
Community iFixit guide: remove the battery door and covers, then swap the front shell. Front covers for the Rebel T3, Kiss X50, and 1100D fit each other.[8]
Special tools: JIS #000 screwdriver, opening picks, spudger, angled tweezers
Good to know
- Front covers for the Rebel T3, Kiss X50, and 1100D are interchangeable.[8]
- The guide rates the job moderate and about 15 minutes.[8]
- Steps include pulling the battery door straight out, removing bottom screws, and unplugging ribbon cables.[8]
⚠ Watch out
- With the front cover off, the high-voltage capacitor on the DC board is exposed. Discharge it before work.[8]
Top cover replacementWorks
- ⚠ Stored charge Capacitors keep a dangerous charge after the device is off.
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
Community iFixit guide through the I/F cover, back cover, and front cover to reach the top assembly. Replacing the top cover or DC board means desoldering four cables to the DC board.[9][8]
Good to know
- The guide rates the job difficult and about 20 to 40 minutes.[9]
- Replacing the top cover or the DC PCB needs the four cables from the top cover to the DC board desoldered.[9]
- The path starts with the I/F terminal cover, then the back-cover ribbons, then the front cover. The microphone cable unplugs from the main board.[9]
⚠ Watch out
Buttons & modes
| What | How |
|---|---|
| Bypass Magic Lantern once | Hold SET at startup.[14] |
Sources (16)
- official EOS REBEL T3/EOS 1100D Specification · 2026-11-16
- official External microphones that can be used with the EOS REBEL T3/EOS 1100D · 2026-11-16
- official EOS Rebel T3 / EOS 1100D Firmware Update, Version 1.0.6 · 2026-11-16
- official magiclantern_simplified/platform at dev · 2026-11-16
- news Canon Announces New Rebel T3/1100D. 720p HD Video. · 2026-11-16
- blog Magic Lantern Raw Video - Current camera capabilities, updated for 2017 · 2026-11-16
- blog Canon EOS Rebel T3 / 1100D | Cameralabs · 2026-11-16
- docs Canon EOS Rebel T3 Front Cover Replacement - iFixit · 2026-11-16
- docs Canon EOS Rebel T3 Top Cover Replacement - iFixit · 2026-11-16
- forum LCD screen and backlight disassembly - Canon EOS Rebel T3 - iFixit · 2026-11-16
- wiki Magic Lantern (firmware) - Wikipedia · 2026-11-15
- official magiclantern_simplified - reticulatedpines · 2026-11-15
- official Magic Lantern INSTALL.txt · 2026-11-15
- official Magic Lantern FAQ.txt · 2026-11-15
- official Magic Lantern FEATURES.txt · 2026-11-15
- blog Will Custom Firmware Void My Warranty? · 2026-11-15