★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 50 device pages approved★ 482 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000054devices tracked

Home › Devices › Nintendo › Game Boy Advance

Game Boy AdvanceNEW!

Photo: Joonas Javanainen (gekkio), CC BY 4.0 · AI-edited (studio background)

NINTENDO · HANDHELD CONSOLE · 2001

Game Boy Advance

Also called: GBA · AGB-001 · original Game Boy Advance

✔ APPROVEDChecked fact by fact · last checked 2026-11-15 · 14 sources · 5 item(s) unverified

The wide original Game Boy Advance, model AGB-001, from 2001. It runs about 15 hours on two AA batteries. Common mods fit an IPS screen (a no-cut kit, or a kit that trims the shell), an SP backlit screen, a rechargeable cell, or a new shell.[1][2][7][4][9][3]

9MODS
5WORK
4EXPERIMENTAL
14SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
AGB-001Original Game Boy Advance2001Model number AGB-001. This is the wide original, not the clamshell SP.[1]
Specs
Size145 × 82 × 24 mm[1]
BatteryAbout 15 hours on two AA batteries[1]

Mods (9)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

No-cut IPS screenWorks
ScreenDifficulty: mediumOpens caseNo solderingReversible

A drop-in IPS kit that leaves the original shell uncut and needs no solder. It has brightness control. You still open the case to fit the screen.[7]

Good to know

  • The kit needs no change to the original case and is plug-and-play.[7]
  • The kit has brightness control.[7]

⚠ Watch out

  • The screen does not seem to be as bright as other options.[7]

Guides:No-cut, no-solder GBA backlit IPS screen mod – RetroRGB

IPS screen with a shell trimWorks
ScreenDifficulty: hardOpens caseBasic solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

An IPS kit for the original shell. Trim the plastic around the screen, or use a pre-trimmed shell. On a 32-pin board, fold the ribbon adapter. Brightness is three wires.[2][6][8]

Parts

  • FunnyPlaying 3.0 inch laminated IPS kit Fits with conditions — Only works with a laminated housing. At the lowest brightness the kit draws about 0.14 W.[6] Buy: funnyplaying.com

Good to know

  • 32-pin boards need the ribbon adapter folded. Skip that step on a 40-pin board.[2]
  • Hold Select and press L to dim the screen. Hold Select and press R to brighten it. That control uses three wires soldered to TP2 (Select), L, and R.[2]
  • The laminated FunnyPlaying kit bonds the glass to the panel. Its on-screen menu keeps settings after power-off, and includes palettes, frame blending, and a pixel grid.[6]
  • Early IPS kits look different from an AGS-101 screen.[8]

⚠ Watch out

  • Trim the shell around the LCD, or start with a shell that is already trimmed.[2]

Guides:Game Boy Advance IPS Backlight mod - iFixit Repair Guide

SP backlit screenWorks
ScreenDifficulty: hardOpens casePermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Fit an AGS-101 screen from a Game Boy Advance SP into the original Advance. The adapter has to match the board, and the shell plastic is cut for the thicker panel.[4]

Good to know

  • The install uses an adapter that matches the motherboard type (32-pin or 40-pin).[4]
  • Internal shell plastic is trimmed so the thicker backlit panel fits.[4]

Guides:Gameboy Advance AGS-101 Blacklight Mod - iFixit Repair Guide

Rechargeable LiPo packExperimental
BatteryDifficulty: easyOpens caseNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

A drop-in LiPo adapter for a 1200 mAh cell, with no shell cutting. It uses a TP4056 USB charge module, Micro-USB or USB-C.[9]

Parts

  • AGB LiPo adapter Fits — Made for a 103040 1200 mAh LiPo and a TP4056 charge board. No shell cutting.[9]

Good to know

  • The adapter is meant to add a rechargeable cell without a permanent change to the console.[9]

Guides:No guide found yet.

New shellWorks
CaseDifficulty: easyOpens caseNo solderingReversible

Move the board into a new housing. The job swaps the front and back shells, the buttons, the rubber pads, and the screen lens.[3]

Special tools: tri-point Y0 screwdriver

Good to know

  • The back shell is seven screws. The motherboard is three more. A tri-point Y0 driver and a JIS driver are used.[3]

Guides:How to Reshell Your Game Boy Advance - iFixit Repair Guide

Laminated 720×480 screenExperimental
ScreenDifficulty: mediumOpens case

A pre-laminated IPS kit at 720×480, with integer scaling of nine new pixels per original pixel, an on-screen menu, and touch shortcuts that can be turned off.[5]

Parts

  • Hispeedido V5 pre-laminated IPS kit Fits — Pre-laminated lens, 720×480, with an on-screen menu. Touch shortcuts can be turned off.[5] Buy: hispeedido.com

Good to know

  • The panel is 720×480 with integer scaling, nine new pixels for each original pixel. The menu includes desaturation and frame blending that can be turned off.[5]

Guides:No guide found yet.

Clicky buttonsExperimental
Buttons & inputDifficulty: hardOpens caseFine solderingPermanent
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

A flex board that replaces the rubber pads with tactile switches, like the SP. It is soldered to the button test pads.[10]

Parts

  • AGB tact flex board Fits — Soldered to the button test pads. Takes ALPS or XKB switches, with a 3D-printed D-pad spacer.[10]

Good to know

  • The board converts the membrane buttons to clicky tact switches.[10]

Guides:No guide found yet.

MIDI linkWorks
ConnectivityDifficulty: mediumCase stays closedNo solderingReversible

An Arduino on the link port talks to a sequencer or DAW. It can take power from the link port. The case stays closed.[12]

Good to know

  • ArduinoBoy was tested on the Game Boy Advance and Advance SP, the original Game Boy, and the Game Boy Color.[12]
  • It plugs into the link port and can be powered from that port.[12]

Guides:No guide found yet.

Replacement motherboardExperimental
OtherDifficulty: expertOpens case
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

An open recreation of the Advance board with a cleaner audio circuit. One variant keeps AA batteries. One uses a lithium-ion cell.[11]

Good to know

  • The project is a new motherboard for the original Advance, with a cleaner audio circuit.[11]
  • Board variants support either the stock AA batteries or a built-in lithium-ion cell.[11]

Guides:No guide found yet.

Sources (14)

SOURCES.TXT