Home › Devices › SNK › Neo Geo Pocket (mono)
NEW!Photo: Evan-Amos, Public domain · AI-edited (studio background)
SNK · HANDHELD CONSOLE · 1998
Neo Geo Pocket (mono)
Also called: NGP · Neo Geo Pocket Classic · SNK Neo Geo Pocket
Japan/Hong Kong monochrome Neo Geo Pocket (eight greys, two AA cells). The common screen work is a Hand Held Legend Game Boy backlight (documented install) or a frontlight; shops also sell a Hispeedido mono IPS kit and a recap/speaker kit. The IPS kits are sold separately for the mono NGP and the NGPC, so pick the one for your console.[8][1][2][6][9]
Which one do I have?
| Model | Variant | Year | How to tell |
|---|---|---|---|
| Neo Geo Pocket | Monochrome (Classic) | 1998 | First NGP: reflective grey LCD, not the Neo Geo Pocket Color. Japan/Hong Kong release.[8] |
Specs
Mods (4)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Game Boy backlight (Hand Held Legend)Works
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Fit an HHL DMG/Pocket V3 backlight behind the mono LCD after removing the polarising foil. About 1–2 hours; case notches and post trimming required.[1][2][4][5][3]
Special tools: Tri-wing screwdriver, scalpel
Parts
- Hand Held Legend Game Boy Backlight V3 (DMG/Pocket) Fits with conditions — Vendor says DMG and Pocket backlights can backlight a Neo Geo Pocket. Soldering required. Run from a 5 V source; no alcohol on the panel.[2][4][5][1] Buy: handheldlegend.com
Good to know
- Hand Held Legend says its Game Boy DMG and Pocket backlights can be used to backlight a Neo Geo Pocket.[2]
- A 2018 install: five Phillips and one Tri-Wing screw, ZIF screen ribbon, desolder speaker wires, remove polarising foil so the LCD is see-through, test-fit film between LCD and backlight, wire to the board, cut case notches and trim top posts.[1]
- The LCD is glued and can crack; dry-run before final fit and clean dust carefully.[1][5]
- Vendor docs: do not use alcohol on the backlight; install at a 5 V source for brightness and to avoid audio-board interference; resistors are built into non-RGB V3 panels.[5]
Guides:Adding a Back Light to a Neo Geo Pocket (not Color)V3 Backlight and Bivert
Neo Geo Pocket frontlightWorks
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
HHL frontlight for NGP or NGPC, installed like Game Boy Color/Advance frontlights. Needs LOCA optical adhesive.[3]
Parts
- Hand Held Legend Neo Geo Pocket Frontlight Fits — Fits mono NGP or Color. LOCA required. Dry-run before install; LCD may break under pressure.[3] Buy: handheldlegend.com
Good to know
- Installed very similarly to the Game Boy Color/Advance frontlights; LOCA is required.[3]
- Do a dry run before installation; the LCD may break under pressure.[3]
Guides:No guide found yet.
Hispeedido Super OSD IPS kit (mono)Experimental
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Full backlit IPS LCD replacement sold for the monochrome NGP (HS-IPS-NGP) with OSD touch controls. NGPC color IPS kits are a separate product.[6][9]
Parts
- Hispeedido Super OSD IPS kit (HS-IPS-NGP) Fits with conditions — Seller claims 5% more screen area, minor soldering, touch sensors for palette/brightness/OSD. Separate kits are sold for NGPC Fat/Slim; pick the kit for your console.[6] Buy: k-retro.com
Good to know
- K-Retro sells a Hispeedido Super OSD IPS kit specifically for the monochrome NGP (and separate kits for NGPC Fat and Slim).[6] unverified
- RetroRGB's IPS write-up covers Neo Geo Pocket Color kits (larger viewable area, custom lens) — not the monochrome console.[9]
Guides:No guide found yet.
Capacitor recap and louder speakerWorks
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
Replace the electrolytic capacitors, power LED, and speaker. Soldering required; seller says the included speaker is louder than stock.[7]
Parts
- K-Retro NGP mono capacitor and speaker kit Fits — Includes electrolytics (4×100 µF 4 V, 1×470 µF 6.3 V), LED, and speaker.[7] Buy: k-retro.com
Good to know
- The kit includes all electrolytic capacitors, a new speaker, and a power LED; soldering is required.[7]
- The seller says the included speaker is louder than the original (demo video is for NGPC).[7] unverified
Guides:No guide found yet.
Sources (9)
- blog Adding a Back Light to a Neo Geo Pocket (not Color) · 2026-11-17
- blog Neo Geo Pocket Backlights! | Hand-Held Legend · 2026-11-17
- shop Neo Geo Pocket Frontlight | Hand-Held Legend · 2026-11-17
- shop Game Boy Backlight Display Mod V3 for DMG and GBP · 2026-11-17
- official V3 Backlight and Bivert · 2026-11-17
- shop Hispeedido Super OSD IPS LCD Mod Kit for Neo Geo Pocket Classic · 2026-11-17
- shop Capacitor Replacement and Refurb Kit with Replacement Speaker for NGP Mono · 2026-11-17
- wiki Neo Geo Pocket - Wikipedia · 2026-11-17
- blog New NGPC Backlit IPS Screen – RetroRGB · 2026-11-15